• Ldap Load Balancing

    Hi, i have a cisco CSS which can balance htttp, tcp and udp protocols. Im trying to balance ldap connections between 2 servers using the tcp protocol but its not working, i´ve read that this is possible. Is there somone that can help me with my cisco load balancer configuration?

    D34095 pointsBadges:
  • How to clear asp routing table on Cisco ASA

    How to clear asp routing table on ASA.

    Superpinky5 pointsBadges:
  • configure automatic switchover from primary to backup tunnel

    Hi All, Some one pl suggest. The scenario is ,we want to configure a backup link to our main branch which is connected to US & we are having dedicated primary link to it & whenever the primary link goes down.Then, we will initiate the backup tunnel from the firewall. We want to configure automatic...

    Vinesh123480 pointsBadges:
  • Cisco Wireless 1200 DHCP Issues

    Ok, I have seen this same issue on several message boards etc. but I have yet to find a good answer so here it goes. I have a network with 12 Cisco 1200 series access points all connecting to 3550PWR switches. The switches are configured with 2 vlans, one for a public wireless LAN and the other as...

    Leeth70 pointsBadges:
  • Cisco ARC Council

    Hello, Does anyone know how to transfer a call directly into voicemail (without ringing)using the ARC council?

    Jimshoe12110 pointsBadges:
  • VLAN Routing

    We have created two VLANs on single Cisco C3560 switch and now want to have inter-VLAN routing. Please explain how to enable it. Please note, we have only one L3 switch, with 10 computers on one VLAN and 10 on other VLAN.

    Swapnilc5 pointsBadges:
  • Configuration between L3 switch 3750 and L2 switch 2960 via trunk port

    I am going to connect three L2 switches 2960 from L3 Switch 3750, means all three L2 switches are connected to L3 switch via trunk switch. Thanks & Regards, And i am going to configure VLANs on L3 Switch. So plz let me suggest,if both switches are in server mode then i should configure VLAN on L3...

    Bhupendra205 pointsBadges:
  • Free Chapter – Implementing Multicast on Cisco Catalyst Switches

    Another free chapter download is available on the IT Bookworm Blog. Written by: David Barnes and Basir Sakandar Book: Cisco LAN Switching Fundamentals Overview: "Cisco LAN Switching Fundamentals provides an easy-to-understand introduction to LAN switching best practices using Cisco Catalyst...

    BrentSheets6,925 pointsBadges:
  • What is meant by SLL? Can you explain? (read at last line of this Cisco paragraph)

    Cisco ASA 5500 Series adaptive security appliances are purpose-built solutions that combine best-of-breed security and VPN services with the innovative Cisco Adaptive Identification and Mitigation (AIM) architecture. Designed as a core component of the Cisco Self-Defending Network, the Cisco ASA...

    Fayas65 pointsBadges:
  • Cisco Networking

    How can we provide load sharing on single router of two ISPs. plz let us suggest on the same.

    Bhupendra205 pointsBadges:
  • Cisco WCS Perfomance Profile question

    In Cisco WCS, when you click CONFIGURE- ACCESS POINTS and on a particular ACCESS POINT you clck on Perfomance Profile we are shown with a bunch of parameters like Max Clients, Min Failed Clients (#), Coverage Level (dB) and Min failed Clients (%) and a few others. But just can't seem to find in the...

    mystergag30 pointsBadges:
  • Two routers configration

    I have configured two routers completly the two router connected by them serial, router 1 can bing to interface e 0 and s 0 of router 2 and router 2 can ping interfaces e 0 an s0 of router 1 but network on e 0 of router 1 cannt bing s0 of router 2 and inverse right what is the problem

    Monkez50 pointsBadges:
  • VLAN route on a stick

    Hello Guys I have some concern regarding my VLAN route on a stick, I created 6 VLAN's on Cisco 1841 router in Ethernet port 0/0 with Local IP 192.168.2.x then I created sub interface in the same ethernet port0/0.10, port0/0.11, port0/0.14, port0/0.15 all VLAN's route to my local default gateway...

    Bsm122045 pointsBadges:
  • Cisco Encryption

    Is there a way to encrypt console port and vty port on a cisco switch/router using type 5 password encryption?

    Jd0085 pointsBadges:
  • How to configure Cisco PIX 525 to record SSH logon connections?

    Configuration PIX 525 ------------ Syslog Server Pix 525 running - 7.0 Pix logging trap has been set to informational Syslog Server - Aix 5.3 ssh logon is not being recorded in syslog All other activities are being logged in syslog

    Trinibree10 pointsBadges:
  • Router Locks Up Every 7 Hours Exactly

    Hi, I am suffering a strange problem with a Cisco 851 router on my network. Exactly 7 hours to the second, the Fastethernet4 port stops accepting traffic. The router is still alive on the LAN side the network still functions and you can still access the router software. I have a 10MB SDL connection...

    Ls21gce25 pointsBadges:
  • Cisco IP phone issue

    We are on the CUCM 6.1 - I have a phone where the vm light and prompt is not working. I don't believe it's the phone because I rebuilt a new phone and am getting the same issue. The other phones at her office do have this issue and each one is setup the same. Is there something outside of the phone...

    Cknafick160 pointsBadges:
  • Easy Vpn Server cisco 3845

    i need to set the TCP on my cisco 3845, right now my easy vpn server is set for UDP and some of my users cant access the vpn due to esp and ike being blocked.

    Noaa365 pointsBadges:
  • Cisco 1841 security bundle

    Hi, I am an heir of a cisco 1841 router with an IOS that doesn't have the security bundle like firewall, QoS, VPN and those other staff that are suppose to be included asside from the basic features. The router is performaing well but I want to uprage its IOS. However, its out of support. Could...

    JuneC155 pointsBadges:
  • Incoming traffic blocked to VLAN

    I've set up a network segment on a VLAN on our office router. The gateway IP for the block on the router can be pinged from the outside world fine. Other numbers from the block can be put on machines plugged into the port on the switch and work for all purposes in going to the outside world, but...

    Jfmays15 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following