• Cisco 2811 Fast Ethernet and LAN configuration

    i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

    JACK15705 pointsBadges:
  • Adding a Route – Cisco router

    I have cisco 1800 series router that i want to add a route for all internet access is routed from the cable router/modem. Right now all the traffic is going over the T1 via cisco router. What i want to do is keep everything as is and only have the internet access route from the other devie. How...

    Kwt712555 pointsBadges:
  • Console Session on cisco router

    Hi                I have two routers in my lab , which  is not accessible via console. one is a cisco 3640 router, it shows some unrecognised characters when accessing via console. i did reset the baud rate jumper ,but no result.               In 2811 router it shows boot up...

    Puli45 pointsBadges:
  • BTS 10200 command definitions

    Are there definitions to the commands on the Cisco BTS 10200 switch whereby I can understand what each command input means

    VOIPEng5 pointsBadges:
  • Networking cisco access point

    i am working on cisco access point 1242 i had default username cisco and password Cisco but when i deleted and changed a new user name and password xxxx what happen, i can telnet through cli mode with new username and password but when i try to take http access the access point take old password...

    Ekansh400 pointsBadges:
  • QOS when receive traffic is more than transmit

    My current bandwidth is 10M. The traffic pattern is usually 2Mb transmit and 8 Mb receive from the ISP. I want to guarantee bandwidth for the WEBEX traffic which i can do for transmit traffic but my problem is that the receive traffic is whats killing me. Is there any way to make sure that my webex...

    Shane6505 pointsBadges:
  • No linestate on several CCM-lines that belongs to Cisco-SEP

    1) Can a SEP (Cisco phone) have several line connections? 2) If yes, what happens with the linestate of the lines if one line is restricted? 3) What does the below log mean? I want a linestate on ext 5228 but gets that line 5229 is restricted? Both lines is connected to same SEP. 2009-08-20...

    Runningisnew10 pointsBadges:
  • Two lines to one cisco-SEP

    What happens if there are two lines as extension mobility (user device profiles) connected/configured to one SEP where one of them is restricted? Does the other line inherit the restricted lines "configuration"?

    Runningisnew10 pointsBadges:
  • What are the similarities in Cisco and HP ProCurve switching protocols?

    like layer 2 protocol in cisco called VTP , while in hp procurve is called GARP , I need to know the other similarities in both for layer 2,3

    Henno5 pointsBadges:
  • Setting up Cisco 2950 switch

    Hello, New to itknowledge exchange... I have a hand me down Cisco 2950 12 port switch. I currently have assigned to my Cable Modem4 Static Public IP's Note: Not real but used for example. 70.66.131.1 70.66.131.2 70.66.131.3 70.66.131.4 I run 3 servers in my basement all of which I have configured...

    Perkster5 pointsBadges:
  • Cisco Access Control Lists – Recommended default template?

    Hey guys! I was hoping to find a default access control list template that you may use to block off, reserved addresses, known worms, viruses, vulnerabilities when you are setting up a new router? Trying to think of every possible threat is impossible but a good recommended starting point for...

    Tkrn10 pointsBadges:
  • .11n Experiences with various wireless AP vendors?

    I'm interested as to IT pros experiences with various wireless AP vendors: What equipment have you found to work well with the .11n standard, and what your experience has been like working with vendors. Were most willing to allow you to try-before-you buy for a major deployment?

    Michael Morisy8,323 pointsBadges:
  • Software based WIN Simulation

    Hi, I need to test out an application over WAN. The testing includes the response time with different delays and bandwidth requirements. Is there any piece of software (preferably opensource/freeware)which can simulate the WAN for me? The idea is to install two NICs in the Windows/Linux machine,...

    SADnBLUE0 pointsBadges:
  • NAT issue with load balancing between two ISPs

    Hello everybody! This is my first question, I am brand new in this so please excuse me if I do not write properly or straight to the point. I will try my best. These are the devices related to my question: - cisco2811 (completely access) - DSL modem - cisco2900 series I have access to all except...

    Okrus5 pointsBadges:
  • Cisco Gatekeepers?

    Does anyone have any good basic instructions on Cisco Gatekeepers?

    HarryK5 pointsBadges:
  • HBA not showing WWN

    A SearchStorage.com reader asks: WE have a data center server, 2003 servers and two HBAs in each node. Both the cards are Emulex Fibre Channel Cards. One card is already in working condition. We have recently added the second HBA card. The driver was updated, and I am able to detect two HBAs from...

    JenH0 pointsBadges:
  • SSH configuration on Cisco router

    Please provide me a step to step detail configuration of SSH. Thanks..

    Vinesh123480 pointsBadges:
  • Cisco IP Phone 7961

    Incoming calls are ringing out instead of first being answered by the auto attendant. Typically when this has happened in the past I've been able to go in and reselect the greeting prompt we created. Problem solved. Now that is no longer working. I did notice the prompt greeting was no. 6...

    Ntfsb5 pointsBadges:
  • I’ve been hacked — I think….

    I'm an IT administrator with a little over 500 end users, running Windows 2000 and XP. One of our users is experiencing a problem with her Internet connection suddenly dropping for no apparent reason. When she restarts her computer, everything works fine for awhile, but then the connection drops...

    LMullen0 pointsBadges:
  • Ldap Load Balancing

    Hi, i have a cisco CSS which can balance htttp, tcp and udp protocols. Im trying to balance ldap connections between 2 servers using the tcp protocol but its not working, i´ve read that this is possible. Is there somone that can help me with my cisco load balancer configuration?

    D34095 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following