• Can I connect a WAP4410N to a Cisco SPA508G phone?

    I have a Cisco SPA508G phone connected over POE to a Cisco ESW520 24-port switch and would like to use the port on the phone to connect a Cisco WAP4410N AP.  Will this work?

    lyleosborne5 pointsBadges:
  • Configuration problem on 2950 port security sticky behavior

    Hi, I am trying to put port security on a port, I want it to shutdown if another computer gets plugged into that port. I followed the following steps: I set these options: switchport mode access switchport port-security switchport port-security maximum 1 switchport port-security violation shutdown...

    Patelmanojk50 pointsBadges:
  • Transistion Training Path

    Hi, we will be transitioning from a digital base PBX to a VoIP system in the upcoming 18 months. We are going to a Cisco base system and would like to know what Cisco or other training would be most beneficial in moving our staff from a analog base system to a VoIP system.

    Angel5 pointsBadges:
  • Using IP helper-address on a VLAN with two subnets

    I am trying to get IP helper-address to be able to pull DHCP addresses from a super scope. Right now it will only pull from the subscope that matches the subnet of the primary subnet for the vlan. Does anyone know of a way around this? Or if there would be an adverse affect on the current DHCP...

    Jfenton5 pointsBadges:
  • Cisco 1548U: A managable switch?

    I have a aCsico 1548U. Unfortunately for a project that I am working on right now we need a manageable switch, and there is a huge lack of funds. Is it possible to make the 1548U into a manageable switch so that I can achieve my goal?

    Jhazard11240 pointsBadges:
  • How do I set up the Cisco ASA 5505?

    I have a static IP address for the Modem and I believe that I set up the outside VLAN2 correctly with another IP address that I have for the ASA. The IP address that I have setup is 192.168.10.1/0 for the pc, and I have set this up as static also. So my question is what is the default gateway for...

    Levelheaded53685 pointsBadges:
  • Free Chapter – Implementing Multicast on Cisco Catalyst Switches

    Another free chapter download is available on the IT Bookworm Blog. Written by: David Barnes and Basir Sakandar Book: Cisco LAN Switching Fundamentals Overview: "Cisco LAN Switching Fundamentals provides an easy-to-understand introduction to LAN switching best practices using Cisco Catalyst...

    BrentSheets6,925 pointsBadges:
  • Cisco VoIP implementation issues

    What are issues may occur when moving from a PBX environment to VoIP solution?

    Brakar5 pointsBadges:
  • Anyone know of a free simulator for Cisco router and switch configuration?

    Can anyone recommend or suggest a free simulator for Cisco router and switch configuration? Thank you!

    NetworkingATE1,545 pointsBadges:
  • CLI config confirmation

    Hi, does anyone know if d-link is manufactured by Cisco? There is this client that asked me on how to create multiple IP addresses on a single interface of Cisco router, but the switch connected to it was a d-link switch. Of course, the solution was intervlan routing but I haven't seen a d-link CLI...

    Yeahboy900 pointsBadges:
  • How do you update Cisco access point 1200?

    How can I update Cisco access point 1200?

    Rossy145 pointsBadges:
  • Cisco VG 2911 configuration manual

    I'm looking for the configuration manual for Cisco VG 2911. Can anyone point me in the right direction?

    charley55 pointsBadges:
  • Cisco 3550 config assistance needed

    Here is the network scenario: I have two T1's coming into our main building. One is a p2p T1 circuit to a remote office. The other is a basic T1 circuit for Internet connectivity. The far end of the p2p is in the 192.168.3.0 255.255.255.0 network. The local router is an Adtran with an IP of...

    Yernkie5 pointsBadges:
  • Cisco 5510 firewall configuration

    How do I configure Cisco firewall 5510 ASA?

    Van helsing60 pointsBadges:
  • Router configuration is not saving in Cisco 2800 router

    I connect the 2800 to the configuration. Once the router is restarted router is going to ROM mode. The router configuration not saving.

    Venuchennu5 pointsBadges:
  • Cisco servers

    Hi, can anyone please tell me what they know about Cisco servers and their features please.

    Jboy5 pointsBadges:
  • How many ports in Cisco 2811 router

    Does anyone how many ports in Cisco 2811 router?

    Ipsr solutiond ltd5 pointsBadges:
  • How can I prepare for the CCNA exam in addition to my college course?

    How would you recommend that I prepare for my CCNA (Cisco Certified Network Associate) exam? I have been taking courses through my college, DeVry University, but I want to be even more prepared. The courses run us through various labs and provide us with additional material for reading. I have read...

    NetworkingATE1,545 pointsBadges:
  • How to dial in to listen to Call Center calls live?

    Hello, currently we use Cacti and Cisco in our call center. Our client is asking us if there is a way that they can dial in and listen to live calls as they are coming in. Is there a way that we can help our client? My understanding is that this is not possible with Cacti and Cisco, but I want to...

    NetworkingATE1,545 pointsBadges:
  • How to configure load balancing on Cisco 1751 router with 2 serial WAN connections?

    How to configure load balancing on Cisco 1751 router with 2 serial WAN connections (different service providers)? Thank you.

    NetworkingATE1,545 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following