Cisco

Where can I find Cisco 2801 regulatory certificates

where can I find cisco 2801 regulatory certificates

Setting up Cisco 2950 switch

Hello, New to itknowledge exchange... I have a hand me down Cisco 2950 12 port switch. I currently have assigned to my Cable Modem4 Static Public IP's Note: Not real but used for example. 70.66.131.1 70.66.131.2 70.66.131.3 70.66.131.4 I run 3 servers in my basement all of which I have...

How to rate limit on Cisco Catalyst 3550-EMI

Hello, I have a cisco switch 3550 EMI and I need to do rate limiting on ethernet ports. class-map match-all 5M description 5M with 500K burst ! policy-map 5M class 5M police 5120000 51200 exceed-action drop interface FastEthernet0/3 switchport access vlan 100 switchport mode dynamic...

Cisco 2811 configuration for managing traffic through two Internet connections

Hi all, I have one cisco 2811 router with serial interface for leased line connection ton internet and an adsl wic for Internet connexion too. What I what is to let http traffic goes through the adsl connexion and other trafic goes through the leased line. IS it possible and how? Thanks

cisco ipsec vpn: vpn up but no traffic/ping

Hi, I'm having some problems setting up an ipsec vpn between a Cisco 851 and a Draytek Vigor 2200E+. the ipsec vpn seems to establish well, passes ipsec phase 2, and shows up as an active ipsec session in both routers. the problem is that i'm unable to ping, or send any traffic, to any of the...

Cisco 2811 PVDM2-24DM Initialising

Dear All Professionals, We have taken on the installation of a Cisco 2811 to make digital communications over ISDN and are requiring assistance with our hardware configuration . We have all the necessary modules and so on however our current problem is: We have the digital modem module in slot 0...

Cisco 3550 config assistance needed

Here is the network scenario: I have two T1's coming into our main building. One is a p2p T1 circuit to a remote office. The other is a basic T1 circuit for Internet connectivity. The far end of the p2p is in the 192.168.3.0 255.255.255.0 network. The local router is an Adtran with an IP of...

Cisco 7905G IP Phone mysteriously unregisters from CallManager

I have 7905G ip phones that mysteriously unregister from call manager. The only way to restore service to phone is to restart phone. Has anyone experienced this?

Load Balancing of Unequal Ethernet Bandwidth

Is it possible to aggregate and then load balance the unequal ethernet circuits like so: I have two ethenet circuits on my Cisco router. Both have equal costs to the next hop. Ethernet Circuit #1- 200M Ethernet Circuit #2 - 100M Can I aggregate both ethernet circuits so that the total amount of...

Avaya 4610SW VoIP Quality Issue - connecting to Cisco Gear

I have had a 5 User - Avaya Long Ongoing, IP Phone quality Issue that connects to a Cisco POE 3560 switch and a 1841 router with a Full T1. No one can figure out the Poor Quality Issue and Pin Point where its coming from. What would be a Good Tool to use to try an Pinpoint - Findout as to what the...

Cisco's 2500 series router and WAN card serial interface differences

What is the difference between the serial interface of 2500 series Cisco routers and the serial interface of WAN cards (WIC-1t)? If there is no difference then is there any data-rate difference between the above two serial interfaces?

Load balancing

what is the Cisco configuration to do the load balancing for 4 MPLS ethernet redundant links in one cisco router

How to configure load balancing on Cisco 1751 router with 2 serial WAN connections?

How to configure load balancing on Cisco 1751 router with 2 serial WAN connections (different service providers)? Thank you.

Cisco 2811 Power Supply Jumper - PS Type

I have replaced a DC supply with an AC 100V but the new power supply doesn not havbe anywhere for the PS Type Jumper connection. What does the PS Type do and can I operate without that connected (as the new power supply has no connector) ? Thanks in Advance.

VPN behind PIX firewall

Hi, I have a PIX firewall and I am trying to make a vpn connection from client machine behind the firewall to a server in another site, with a public IP. I am getting error 800. need help please

What are the similarities in Cisco and HP ProCurve switching protocols?

like layer 2 protocol in cisco called VTP , while in hp procurve is called GARP , I need to know the other similarities in both for layer 2,3

QoS value configuration in Cisco 4506 switch

One of our customer required QOS value to be set in two vlan interfaces, they have the required values are as below: 802.1P/Q PARAMETERS IPSI Control Diff Serv.  48 Call Control 802.1p Priority 40 Audio 802.1p Priority 46 Video 802.1p Priority n/a DIFFSERV/TOS PARAMETERS IPSI Control...

Cisco 5510 firewall configuration

how do i configure cisco firewall 5510 asa?

Cisco Unity Switch Data

Is there a way to pull the phone data off of a Cisco Unity Switch without a specific Unity server?

Port Forwarding with Cisco 3560

Hi Friends, I have a small requirement. please see my configuration. i have an L3 switch (Cisco 3560) series and now i am forwarding all the traffic from my network to Firewall from L3 switch through this default route " ip route 0.0.0.0 0.0.0.0 10.11.12.2" where 10.11.12.1 is...