• Cisco Catalyst Express 520 Switch Console?

    I have just taken delivery of a the above mentioned switch. It doesnt have a console port, does anyone have any idea how to access the IOS?

    BlackBullet30 pointsBadges:
  • Securing against rogue DHCP servers

    Looking for an example of how to configure Cisco DHCP snooping. Can someone provide example settings - or point me in the right direction? Many thanks. Moderator Note: This is a user submitted question

    BrentSheets6,925 pointsBadges:
  • How can I disable browsing from my 2960 switch?

    Can I disable browsing option on my 2960 switch for protecting from some users. What command I can use for this?

    Intrnetworking30 pointsBadges:
  • Bladecenter ESX server Vlan problem

    Hello, The bladecenter was initially setup by a company and allows me to only create VM's from Vlan 2. The issue is that I am out of Ip's in that vlan and I wanted the ability to use another address space for the VM's. I've already created a new vlan 20. Here is the current config of the switch....

    Gillron5 pointsBadges:
  • Avaya 4610SW VoIP Quality Issue – connecting to Cisco Gear

    I have had a 5 User - Avaya Long Ongoing, IP Phone quality Issue that connects to a Cisco POE 3560 switch and a 1841 router with a Full T1. No one can figure out the Poor Quality Issue and Pin Point where its coming from. What would be a Good Tool to use to try an Pinpoint - Findout as to what the...

    DNelson5 pointsBadges:
  • How to connect leased line to two locations without router

    I have one 2mbps point to point lease line and two g.703 modem and want to connect two locations having same network wiht that lease line without any router only wiht the help of cisco swith please send me the diagram for the same and tell me how to do that?

    Kuntalmondal9010 pointsBadges:
  • Cisco switch for iSCSI SAN

    A SearchStorage.com reader recently asked: I was wondering if you could recommend a Cisco switch that can be used for Exchange to SAN (NetApp FAS960C) iSCSI connectivity.

    Andrew Burton220 pointsBadges:
  • QoS value configuration in Cisco 4506 switch

    One of our customer required QOS value to be set in two vlan interfaces, they have the required values are as below: 802.1P/Q PARAMETERS IPSI Control Diff Serv.  48 Call Control 802.1p Priority 40 Audio 802.1p Priority 46 Video 802.1p Priority n/a DIFFSERV/TOS PARAMETERS IPSI Control 802.1p 6 Call...

    Kalamm995 pointsBadges:
  • Cisco Unity Switch Data

    Is there a way to pull the phone data off of a Cisco Unity Switch without a specific Unity server?

    Roberthjr5 pointsBadges:
  • How to confiqure QoS in Cisco 6500 Switches

    Dear Friends, I am planning to configure QOS in our network which comprises of Cisco 6500 Series Swicthes as Core/Distribution and Cisco 3560 Switches as Edge Swicthes. We don't have any IP telephony services. Please let me know the sample configurations.

    Yasir Irfan5,550 pointsBadges:
  • Bandwidth Limit on Cisco 3550 catalyst switch on Fast ethernet

    Dear friend, I have a cisco 3350 catalyst switch, I want to limit bandith on that interface to 64kbps, I need help on this. I need to know another way of limiting the bandwith using access list on the ip address assigned to the host on that interface. send your replty to raj_741976@sify.com

    Somaraju5 pointsBadges:
  • Cisco 3550 Failover

    Hi, I am wondering if there is any failover (active- active or active-passive) solution for 3550 switches. I just would like to sync configurations of two 3550 as backup of each other. Thank you for your time in reading/responding my question. Emre.

    Emrecelebi5 pointsBadges:
  • cisco L3 switches 3130G (bladeswitches)

    Hi, Is someone familiar with the cisco 3130G balde swiches? I have a duplex problem with internal fa ports, these are connected internal in the blade chassis. You can't change the duplex speed. I also checked the duplex speed at the esx servers, thats ok. Could it be a defect messanine card? Br,

    CHD5 pointsBadges:
  • Problem with EtherChannel

    Hi everyone I have configured etherchannel on two cisco switches and have enabled on mode. The problem I am having is that the etherchannel link disconnects from time to time for about 5-6sec then comes back on. The wierd thing is that when I display the logging history I get some pagp messages...

    Mstefo15 pointsBadges:
  • Putting it together Cisco Router and Switch

    can someone please tell me how to get a cisco router and a cisco switch hooked up to my home network so it can be my lab with access to the outside world via my home network non-cisco router? I'm tired of pulling my hair out.

    Rob1715 pointsBadges:
  • MDI OR MDIX Configuration

    Is MDI OR MDIX configurable on a Cisco Switch?

    Surferdargent5 pointsBadges:
  • 4900m testin

    how would I cable up 2 cisco swicthes to an IXIA traffic generator for testing. I am testing 4 ports. Would I reun a crossover from swicth 2 switch on the 4 ports.

    Lenyo120 pointsBadges:
  • RFC and Polycom Video

    We have a Polycom video system that times out after about two hours. Someone mentioned that RFC in our Cisco switches could be the problem. I Google on RFC and got a zillion responses. Can anyone steer us in the "right" direction to see if this the problem and possible solutions? Thanks Randy

    Randyspst5 pointsBadges:
  • Channeling Problems Cisco 2960 switches

    While trying to channel two cisco 2960 switches there tends to be a network problem...everything goes down. Could this be the way the switches configurations were set up?

    Tayetaye5 pointsBadges:
  • How to learn more about programming Cisco switches and configuring networks for your career

    I am a voice person and now venturing more into data networking. I have taken some Cisco classes in the past, with global knowledge paid by the company where I worked. So I am wondering now how I can improve my knowledge to get into programming Cisco switches and configuring networks. I have just...

    NetworkingATE1,545 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following