• Cisco Networking

    We have Cisco 4506 Switch, At one incidence it got down due to uncertain power failure. I dont know how to boot it again when power will up

    Ekansh400 pointsBadges:
  • Networking

    show ip arp | in [em]ip address[/em] This command is used to find mac address and Switch port of ip address, but how can we find IP Address from Mac Address in Cisco Switches ?

    Ekansh400 pointsBadges:
  • VLANS and cisco 2960 switch

    VLANS and cisco 2960 I have a new cisco 2960 switch gig 0/1 connecting to a 3560 on gig0/9. the problems is my vlans will not come up. I have configured another switch the same exact way and it works fine. The only line in the commands of bith switches that is different is ip http secure-server.

    ITKE352,395 pointsBadges:
  • Cisco 3750 Switch Script

    I have 50 switches of cisco 3750 POE model. Do any one has a script for Shuting down the POE ports after office hour , which will help to save the power used by cisco IP Phone. If any one have it , please do mail me the link or code on below mail id sunny.sehgal@in.ey.com Reards Sunny Sehgal

    8SU15 pointsBadges:
  • Commands for binding or mapping Layer 2 data to Layer 3 ports

    I have a question concerning Layer 2 and Layer 3 data on the same device. We have a client that will be sending us Layer 2 data streams, but we have to send them to a device that will only take IP multicasts. We will be using a Cisco 7600 Router with a 6700 Switch Card installed. If this is...

    NetworkingATE1,545 pointsBadges:
  • Routing Public Emergency Calls Based on Cell of Origin

    Is it possible to route emergency calls based on the Cell of origin? In a private network, there is one subscriber who wants all emergency calls originating in one specific area to be routed to a special emergency desk. All other emergency calls within the network would be routed to a different...

    Amawhinn15 pointsBadges:
  • Optimized network Diagram

    Hi I have two Cisco 3750 redundant switches, a BlueCoat, an exchange server, a microwave connection, I want to connect them to a Cisco ASA 5510, and make a DMZ for the exchange server, Please some one give me an optimized diagram for the connection of those devices.

    Qma15jo55 pointsBadges:
  • comparacion entre switches 2950 y 2960

    Necesito saber dado a algunas recomendaciones que me han llegado ¿que ganaria pasando de un switch 2950 a un 2960? administra mejor las vlans??es mas rapido??etc agradeceria sus comentarios y opiniones personales hacerca de los aparatos ***************************** I need to know given to some...

    Ald2030 pointsBadges:
  • problem encountered between 3com 4950 to catalyst 500

    I encountered a problem between the connection of 3 com (4950) to catalyst express 500. 3 com is located in the server room and act as our distribution switch, from server room it is connected to catalyst 500 using fiber optic cable (multi mode). I connect the 3 com to the sfp uplink of the...

    Ninja185 pointsBadges:
  • Configuration between L3 switch 3750 and L2 switch 2960 via trunk port

    I am going to connect three L2 switches 2960 from L3 Switch 3750, means all three L2 switches are connected to L3 switch via trunk switch. Thanks & Regards, And i am going to configure VLANs on L3 Switch. So plz let me suggest,if both switches are in server mode then i should configure VLAN on L3...

    Bhupendra205 pointsBadges:
  • Cisco 3524 and 2610 vlans

    Hi im trying to get my head round if this is at all possible. i have a load of 3524 switches and a single 2620 with 1 ethernet port. is it possible to have setup in this configuration with the equipment i have this part i am ok with and understand vlan6 - switch management 10.0.6.1/24 gw...

    Harmlessworld5 pointsBadges:
  • How to create VLAN with this Cisco configuration

    Dear Sir, I have 1) DNS & Exchng Server 2003 with DHCP enabled Win2003 Standard Edtn SP2 , 2) ISA 2006 3) Trend Micro Antivirus Server. I have to create VLAN for 3 Dept. with having 3750 Cisco Switch as routing ( Trunk ) Using 2950 Cisco Switch 2950 VLAN10 High management VLAN11Low management...

    Abduljaleel5 pointsBadges:
  • Cisco Catalyst WS-C6506 – link termination question

    I need Help for one of our solution on our site. Senario We have a simple campus network on our site where we have Core, dist.and access Switches. Two Core Switches that are C6506 having redundancy. CAT6507 Chasis WS-C6506 SUP WS-X6K-SUP1A-2GE MSFC-2 WS-F6K-MSFC2 1000BaseX Ethernet WS-X6416-GBIC We...

    Chitah10 pointsBadges:
  • Fiber Ports on Cisco 2950 24 port switch

    I have fiber connected to my 2950 but it does not work. I did a light test with the fiber strands and they are good. Is there anything else tyhat I am missing that must be done.

    Livesquad5 pointsBadges:
  • Performance of Cisco 3750 Layer 3 switch

    Hi guys, I have a cisco 3750 series L3 switch. It can currently handle 3GB of L2 traffic with no problem, but when faced with 40MB of L3 traffic, CPU utilization shot so high that I can't even telnet to the switch. Could anyone enlighten me please? Thanks in advance!!

    Bluezerk15 pointsBadges:
  • How can i configure a port for multiple vlan at Netgear FS728TS (like “trunk port” at cisco switch)

    i have an Netgear FS728TS switch and i have to use 2 vlan with an cisco switch. (i have no problem about cisco switch configuration) vlan name=Default vlan ID=1 vlan name=AP vlan ID=307 there is F/O cable connection between two switches. 1/g1 port using for this F/O connection at Netgear switch. in...

    Myselfziro5 pointsBadges:
  • How to restore the start-up configuration of a Cisco switch

    I have a 2950 Cisco switch, the command that I used is "erase startup-config". After using this command I reloaded the switch and when it asked me to save the changes I said yes. Now whenever I use the switch it does not take me to the user prompt anymore but in fact all I get is switch: I think my...

    NetworkingATE1,545 pointsBadges:
  • On a Cisco Catalyst 6500, both supervisor cards in hybrid mode sync up automatically in terms of both operating system and configuration

    On a Cisco Catalyst 6500, both supervisor cards in hybrid mode sync up automatically in terms of both operating system and configuration

    Looses10 pointsBadges:
  • Bladecenter T + JS20+ cisco 25R5391 SOL

    I have a bladecenter T and a js20 powerpc blade, as well as a cisco 25R5391 Layer 2 switch. I am trying to establish a serial over lan session to the js20 blade, but the sol status shows 'not ready' even after i add all the switch ports to the same vlan. on another note the 4 external ports on the...

    Baseline0x035 pointsBadges:
  • How to set up a disaster recovery (DR) VLAN to replicate data

    I am new to disaster recovery (DR) and IT management. I have a production site with Cisco switches, and I'm backing up data to a storage area network (SAN). I have a GB link to a remote office and would like to replicate data to another SAN at the remote location. How do I set up a DR virtual LAN...

    NetworkingATE1,545 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following