• VLAN per switch limitation?

    I have a Minolta server and copier which need to communicate across two switches - where these switches have a vlan per switch limitation. From what I can see in a Wireshark sample, the printer is trying to establish communications with the server using broadcast traffic. Is is possible for this...

    Smidgen5 pointsBadges:
  • Cisco 1548U: A managable switch?

    I have a aCsico 1548U.  Unfortunately for a project that I am working on right now we need a managable switch, and there is a huge lack of funds.  Is it possible to make the 1548U into a managable switch so that I can achieve my goal?

    Jhazard11240 pointsBadges:
  • STP Altn BLK port is green

    Can any one tell me why the block port, which I thoght should be amber, is green?  I have 2 x 2950 swtiches and 2 x 3550 swtich, all initial config (no config), connected to each other with cross cables. Everything seems to work as it should when check with IOS display, but all ports are green,...

    Smanodam25 pointsBadges:
  • setting up a TRUNK on cisco switch

    I want to know if there is a to combine different subnet on one cisco 2950 switch with trunking ... i have .0, .31. and .9. If someone can give me an example. that would be wonderful. Right now i have one trunk going to the attic switch from the main switch room which is .35.

    Kwt712555 pointsBadges:
  • Best Web managed switch? HP Procurve or Cisco

    Loking for a webmanaged switch. Nothing fancy but want to be able to add a few VLANs etc. Was ooking at the Procurve 1700/18000. Does anyone reommend HP over Cisco or any other vendor i should be looking at.

    ITKE350,820 pointsBadges:
  • mac addresses on cisco switches

    where do you get the mac addresses to statically configure ports on a switch? why would you need to connect 2 switches together? ccna study. thanks any info. appreciated.

    1010111015 pointsBadges:
  • ciscl acl

    i have 3 core switches having 40 vlans users in vlan 40 only communicate with vlan 40 and other should  be deny except one ip 192.168.5.25 can access to vlan. no hsrp for the vlan 40 configured. root bridge for vlan 40 is core 3 switch. i try various ways but i am not able to do exact and specific...

    Ekansh400 pointsBadges:
  • installing a new switch

    What all needs to be done when upgrading and adding new switches where old ones exist

    Rmullis5 pointsBadges:
  • Monitoring network end user operation with a cisco router

    Hi    One of my client requires a solution for monitoring end users traffic  going through a cisco  router.There is a lot of problem with over utilisation of WAN link by end users. The company need a solution for monitoring operation of end users(who & where they are trying to communicate).  ...

    Puli45 pointsBadges:
  • BTS 10200 command definitions

    Are there definitions to the commands on the Cisco BTS 10200 switch whereby I can understand what each command input means

    VOIPEng5 pointsBadges:
  • Cisco ACL deny icmp

    I have three cisco core 4506 and working with 20 different vlans. i am trying to create deny icmp for vlan 67 subnet 192.168.40.0 255.255.255.224. i tried in many way but i am fail. any host can ping to this subnet and this subnet can ping to any host. but i want to deny for both.  

    Ekansh400 pointsBadges:
  • What are the similarities in Cisco and HP ProCurve switching protocols?

    like layer 2 protocol in cisco called VTP , while in hp procurve is called GARP , I need to know the other similarities in both for layer 2,3

    Henno5 pointsBadges:
  • Setting up Cisco 2950 switch

    Hello, New to itknowledge exchange... I have a hand me down Cisco 2950 12 port switch. I currently have assigned to my Cable Modem4 Static Public IP's Note: Not real but used for example. 70.66.131.1 70.66.131.2 70.66.131.3 70.66.131.4 I run 3 servers in my basement all of which I have configured...

    Perkster5 pointsBadges:
  • Can’t connect D-Link media converter with Cisco switch 2950

    I am using Cisco switch 2950 connected with a D-Link media converter. When power is reset, that switch is up but the port connected with the media converter is down. After I reset power of the media converter, the link comes up. What's going on here, and how can I fix this?

    NetworkingATE1,545 pointsBadges:
  • Cisco Networking

    We have Cisco 4506 Switch, At one incidence it got down due to uncertain power failure. I dont know how to boot it again when power will up

    Ekansh400 pointsBadges:
  • Networking

    show ip arp | in [em]ip address[/em] This command is used to find mac address and Switch port of ip address, but how can we find IP Address from Mac Address in Cisco Switches ?

    Ekansh400 pointsBadges:
  • VLANS and cisco 2960 switch

    VLANS and cisco 2960 I have a new cisco 2960 switch gig 0/1 connecting to a 3560 on gig0/9. the problems is my vlans will not come up. I have configured another switch the same exact way and it works fine. The only line in the commands of bith switches that is different is ip http secure-server.

    ITKE350,820 pointsBadges:
  • Cisco 3750 Switch Script

    I have 50 switches of cisco 3750 POE model. Do any one has a script for Shuting down the POE ports after office hour , which will help to save the power used by cisco IP Phone. If any one have it , please do mail me the link or code on below mail id sunny.sehgal@in.ey.com Reards Sunny Sehgal

    8SU15 pointsBadges:
  • Commands for binding or mapping Layer 2 data to Layer 3 ports

    I have a question concerning Layer 2 and Layer 3 data on the same device. We have a client that will be sending us Layer 2 data streams, but we have to send them to a device that will only take IP multicasts. We will be using a Cisco 7600 Router with a 6700 Switch Card installed. If this is...

    NetworkingATE1,545 pointsBadges:
  • Routing Public Emergency Calls Based on Cell of Origin

    Is it possible to route emergency calls based on the Cell of origin? In a private network, there is one subscriber who wants all emergency calls originating in one specific area to be routed to a special emergency desk. All other emergency calls within the network would be routed to a different...

    Amawhinn15 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following