• Cisco layer 3

    what command do we use for a layer 3 switch so it can also act as a router

    Blangco5 pointsBadges:
  • Basic Cisco Switch Setup for Home Network

    I recently aquired a Cisco 3500xl switch and have 0 experience setting switches up.  I've been searching the nets for a few days trying to find a simple tutorial for setting this switch up for a home network.  I don't need to create separate VLans or do anything complicated.  I basically want to...

    SpiderSpartan20 pointsBadges:
  • Image upgrade

    Hi all I want to upgrade the image of cisco switch 3750 12 S from c3750-ipbasek9-mz.122-55.SE5.bin  to  c3750-ipservicesk9-mz.122-55.SE5.bin so my question is if I bought one image can I install it to more than one switch same model.   Thanks

    Monkez50 pointsBadges:
  • Cisco switch configuration?

    [strong]I have one distribution switch(Cisco) and linked to many access swtitches(d-link) what type of configuration should I do???[/strong] [strong]No VLAN in my network[/strong]

  • Cisco switch configuration

    what is a basi steps in configuring a 2960 cisco switch

    Alexyb5 pointsBadges:
  • Outdiscard Errors

    I'm seeing a lot of outdiscard errors on a port, but bandwidth used is not excessive , speed and duplex are 1000 full. I can't see what could be causing the problem. There are no other errors on the port to point to cable issue etc - any idea what could be causing it? Port Align-Err FCS-Err...

    Jlymn40 pointsBadges:
  • Different Vlans can communicate

    I have two PC connected on a single switch under different vlans ,,, now i want both to talk to each other how this is possible

    Surajg5 pointsBadges:
  • Security firewall in routers

    how do i disable the firewall in the ericson w35 router because it blocking some of my programs from working properly . it says my nat port is blocked

    Jaw645 pointsBadges:
  • Propagating vlan’s over a eigrp?

    Hello, I have 2 switches - one in building X and the other in building Y. The buildings are connected via fiber and eigrp is the protocol that's setup between them. The buildings are p2p connections between 7200's. I need the Vlans to be propagated from switch "y" to switch "x" over the L3...

    Dialerstring5 pointsBadges:
  • Making a virtual NAS out of a server

    I have a I couple of rackmount servers that have Raid f drives set up and running ESXi 4.1  I am trying not to purchase a NAS as this is a pretty small scale project.  Anyone have experience using a software solution to make the DAS drives in the servers look like a NAS that both server can...

    Bet5 pointsBadges:
  • QLogic HBA card not showing on MDS switch database

    I have just added a new blade server HP PROLIANT BL 465 G7 to a HP C7000 ENCLOSURE.  The server was installed on slot 4 of the blade enclosure.  It has a QLOGIC hba installed on it.  There is no operating system installed.  The  fibre cable has been connected to the pass through module at the...

    MZithulele5 pointsBadges:
  • InterVlan on Cisco 3560G series switch and Internet Access

    I have a cisco 3560G and 2911 series router.The Router has 2 internet interface.One is already configured to an unmanaged switch.The second interface is also configure and it can go to the internet.My task is to configure vlans on the switch and the vlans should communicate with each others.Also...

    ralph12360 pointsBadges:
  • Merging Home Network With Cisco Lab

    I currently have 3 Cisco routers, 2 L3 Switches and 4 L2 Switches. I ran a cable from my home Cisco wireless E3000 router to one of my L3 Switches. I converted the switch port that its plugged into as a routed port and to obtain an address using dhcp, which it did grab one. I tested connectivity to...

    Santucci475 pointsBadges:
  • Cisco 2960s switch port config voip with Avaya phone

    Need to know what the switch port configuration would look like for a cisco 2960s switch with an Avaya ip 9611G phone and pc connected to the phone.

    rsc11110 pointsBadges:
  • Optimize Multicast with deployement ghost image (2960 connected 3750)

    Hi, How methode to Optimize Multicast with deployement ghost image (2960 connected 3750). Because, since i have switch cisco the bandwith decrease for image deploy. The bandwith very slow ?. The igmp snooiping has activate. Best regards.

    Hben35 pointsBadges:
  • Network Security appliances

    What are the key things to consider when choosing a network security appliance for 130 user network? I am confused with the plethora of appliances Cisco has on offer.  Network is laid across three floors, with all the switches connecting back to a wiring closet. 

    Bha77a40 pointsBadges:
  • Anyone know of a free simulator for Cisco router and switch configuration?

    Can anyone recommend or suggest a free simulator for Cisco router and switch configuration? Thank you!

    NetworkingATE1,545 pointsBadges:
  • Configuring Cisco and HP Switches

    Can an HP ProCurve switch be configured to work with a Cisco switch? Say a for example 3750 or 6506.  By work I mean, be able to use VLANs create on Cisco side to work on HP side.  Also, for a Cisco trunk to work with on an HP switch.

    Jdleon85 pointsBadges:
  • Cisco 2524 router trying to set up a home lab to study for the ccna exam

    My question is i have a 2524 router trying to set up a home lab to study for the ccna exam and i also have a 2924 xl switch the router has only ethernet 0 and 1..My quetion is can i connect the 2524 router to the 2924 switch which uses fast ethernet..would it make any difference in speed

    Clavender7910 pointsBadges:
  • Mac access list

    hello , almost i disconnect any computer in my lan by making ip access list  in core switch but alway ip in changed for any computer so i try to make mac access list to disconnect any computer depending on it's mac address but in cisco devices there isn't any ability to make this can you help...

    Osamam815 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following