• what this command means in 1841 router config

    what this command means in 1841 router config "ip admission max-nodata-conns 3"

    Florish5 pointsBadges:
  • problems to install SDM in a 2620XM router

    Hi, I tried to install the SDM in my router and pc. In my pc there is not problem, but, when I try to install or connect from my pc always I´ve got the same error:" it is not possible to connect with the router for installing SDM". The router is an 2620XM I have configured an IP address in the...

    Dunkel30 pointsBadges:
  • commands for nortel ARN router against cisco 1700 series router

    as i was using cisco router and now i want to installed nortel ARN router in place of that. I have configuration backup of cisco router,so i only want Nortel ARN router commands to configure against cisco commands

    Networkfresher5 pointsBadges:
  • Network problems Cisco router config

    Hi experts, I want to connect with a web server in remote end using leased line connectivity through Cisco 2800 series router I have a flat network with 500 users in network. All PC’s default gateways are configured the IP of routers Ethernet. When I am ping the web server from LAN it is taking...

    Intrnetworking30 pointsBadges:
  • Cisco 2811 Fast Ethernet and LAN configuration

    i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

    JACK15705 pointsBadges:
  • Tricky EIGRP routing quesiton

    Hello Sudhanshu, I have a bit of a tricky question that I've been wondering about. I'm going to be setting up over a dozen new ASA5510s in front of preexisting 2821 routers. I currently have EIGRP running in GRE tunnels between the sites. I have heard that the ASAs do not support GRE tunnels...yet...

    Richardvoyageur40 pointsBadges:
  • Adding a Route – Cisco router

    I have cisco 1800 series router that i want to add a route for all internet access is routed from the cable router/modem. Right now all the traffic is going over the T1 via cisco router. What i want to do is keep everything as is and only have the internet access route from the other devie. How...

    Kwt712555 pointsBadges:
  • Cisco 3700 router with 2 seperate networks

    i have 2 different networks (181 and 180) running to the same router. i would like for them to "talk" to each other. how would i do this?

    ITKE346,470 pointsBadges:
  • Monitoring network end user operation with a cisco router

    Hi    One of my client requires a solution for monitoring end users traffic  going through a cisco  router.There is a lot of problem with over utilisation of WAN link by end users. The company need a solution for monitoring operation of end users(who & where they are trying to communicate).  ...

    Puli45 pointsBadges:
  • No ‘Total Data’ intervals encrementing on a 2651 router

    Have a 2651 Cisco router with a 4wire T1 WIC card. It has a 768k Frame ckt riding it. When T1 is taking hits or even when it isn't the show service-module never increments stats. It is always (last 0 15 minute intervals) when it should be going up to 96 15 min intervals. Can't find any info on why...

    Jab645 pointsBadges:
  • Console Session on cisco router

    Hi                I have two routers in my lab , which  is not accessible via console. one is a cisco 3640 router, it shows some unrecognised characters when accessing via console. i did reset the baud rate jumper ,but no result.               In 2811 router it shows boot up...

    Puli45 pointsBadges:
  • ROUTER INTERFACE

    IN ROUTER , ON SERIAL INTERFACE I AM GETTING POO RELY 201/255       WHAT CAN BE PROBLEM

    VADERA10 pointsBadges:
  • SNMPv3 Configuration with HP OV

    I am trying to configure snmpv3 using HP OV on a cisco router. The router has been configured properly to run snmpv3 already. I then edited the mgr.cnf file on the server located at /etc/srconf/mgr to add the following entry: usmUserEntry "agentEngineID" snmpv3user usmHMACMD5AuthProtocol...

    Phrathepmali30 pointsBadges:
  • DLink and Cisco Routers

    Can Dlink switch works with a cisco router?

    Microsys5 pointsBadges:
  • how to exit rxboot in cisco 2511 router…..

    how to exit rxboot in cisco 2511 router

    Kaja20048055 pointsBadges:
  • Cisco router password

    I have 1841 cisco router and I forgot the password, so how i can reconfig the password agin

    Mohadbazzi47170 pointsBadges:
  • Can you combine two 64 ISDN BRI channels into one 128 line?

    We have two ISDN lines of 2b+d (BRI) channels. The objective is to get a single B Channel (64) from one ISDN line and another B of 64 from another line and combine it to 128. We are using Cisco's 2621XM router. Can we do that? Is it possible to combine two B channels from different lines to one 128...

    NetworkingATE1,545 pointsBadges:
  • VPN Pass-Through Cisco 871

    Hi All, I'm trying to setup VPN pass-through on a Cisco 871 router.  I have to admit, I'm not very knowledgeable on VPN, let alone doing it on a Cisco router.  I referenced a Cisco document building this config, but can't seem to get it to work. Here's where I am currently at:  I can access the...

    Nfantis55 pointsBadges:
  • change router software version

    i want to change my router software version but i do not know what to do after download the software from cisco website to my pc I how I will copy the software from my pc to the router??

    Mohadbazzi47170 pointsBadges:
  • cisco routers

    how to deny download from internet for spesfic ip address by cisco router please step by step

    Monkez50 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following