• configuration of auxilary port for cisco router

    Hi, We need to configure a adapter for third party. vendor need to login via pstn thorugh this router. i can configure the cisco fax adopter but i dont know how vendor will login to this router please explain. can any body describe what is the scenario "login through aux port via pstn line"

    Ekansh400 pointsBadges:
  • d-link switch to cisco router

    how can I include 3 ip addresses in a single fast ethernet port of a cisco router if the switch connected to that port is a d-link switch? do i have to create subinterface on that fast ethernet port?  

    Yeahboy900 pointsBadges:
  • Bandwith distributions in CMTS

    hi to evreyone" ; can u discuss me on how to distribute or how to control a bandwith inside the CMTS.WHAT migth be the software program that we are going to used in order to control the bandwith in each menimum priorities in terms of Kbps? pls help me ''.. thank you very much. Arnel,

    03062620 pointsBadges:
  • Dumping 7 Cisco routers on a LAN simultaneously?

    Is there a method to dump the configuration of seven Cisco routers on a LAN at the same time?

    TeachMeIT975 pointsBadges:
  • DHCP on a Cisco Router

    Hi, I have 2511 and 2515 cisco routers but  i am unable to get DHCP on the two routers, Pull down screen done's not have DHCP ,Import DHCP not working, Service DHCP not working how can I enable DHCP. Thk , Asanka.

    Asanka5 pointsBadges:
  • Is it difficult/expensive to increase the ‘flash memory’ for a Cisco 800 router series?

    is it difficult/expensive to increase the 'flash memory' for a cisco 800 router series? I understand to use the GUI on the 800 series it needs more memory , thereore i'm curious to know how much/difficulty this is. appreciated. PT

    Pelvicthrust170 pointsBadges:
  • Cisco Router 2801 loads in ROMMON mode

    Hello There, basically i have a router Cisco 2801 when i turn it ON then it load and come to the ROMMON mode and giving the following error. " %C3600-3-SLOTS: Number of slots in chassis is undefined. %SMC-2-BAD_ID_HW: Failed Identification Test in 0/-1/-1 [1/0] The module in 0/-1/-1 in this router...

    Ahmer10 pointsBadges:
  • Flows Data through a Pix 515E firewall

    The flows data originates from a Cisco 1841 router outside the firewall at 200.100.1.1 A 'show ip cache flow' and a packet cap outside the fw shows data flowing. The flows port in use is 2055. Inside the firewall is a local machine 10.10.19.4/16 to capture the data. But no data arrives. On the Pix...

    Pixteck20 pointsBadges:
  • Tacacs and authentication on Cisco routers

    We have ACS 3.X server for tacacs + and radius authentication in our lan switches. right now i am able to login through tacacs+ only. I want to enable tacacs+ as well as local telnet login . This will help me to login in switches if the tacacs will fail.

    Ekansh400 pointsBadges:
  • Load balance on WAN interface using static router between two ISP

    By using static router, i need to configure two lease line of 3 mbps and failover

    Pranab12310 pointsBadges:
  • Enabling QOS on Windows Server 2003 network

    How do I enable QOS on my network as we are introducing soft phones and IP phones to our network? The network has Windows 2003 servers, a sonicwall FW and a cisco router.

    Karl Gechlik9,860 pointsBadges:
  • Creating a bonded T1 for our data center

    We have two T1 connections coming into two cisco routers. The lines are from different providers. Can we make them into a bonded t1 for our data center? What equipment will we need and what configuration?

    NewnanIT1,110 pointsBadges:
  • Free IT Book: Next-Generation Data Center Architectures from Cisco

    This week's free IT book is your complete guide to planning, configuring, managing and troubleshooting NX-OS in enterprise environments: NX-OS and Cisco Nexus Switching. For your copy of this great resource for Next-Generation Data Center Architectures, simply answer one of five questions below and...

    MelanieYarbrough6,345 pointsBadges:
  • Suggestions for Cisco NetFlow analysis tools

    What tools are other members using for Cisco NetFlow traffic analysis? I'm especially interested in open source tools but any commercial or proprietary recommendations or suggestions would also be appreciated. Thank you. Moderator Note: This is a user submitted question

    BrentSheets6,925 pointsBadges:
  • Updating firmware on IOS Cisco router

    Our firmware on our IOS Cisco router is outdated. We have been tasked to update it to the latest version. How can we do this? Where do we get the file from and what is a fttp server and how do we use it in conjunction with flashing the box?

    NewnanIT1,110 pointsBadges:
  • Locked out of Cisco Router – Password reset doesn’t work

    do work for a local non-profit group. Apparently some prior network admin left under unhappy circumstances and did something to the cisco router(s) there. We had no password access, so I went through the password recovery/reset procedure. Everything seemed to be fine except for two little details:...

    Bobkberg1,070 pointsBadges:
  • Deploying VOIP and QOS

    We want to deploy VOIP to our network. We first need to implement QOS how can we do that? We have all HP switches and Cisco routers. The firewall is also a Cisco (PIX).

    Karl Gechlik9,860 pointsBadges:
  • VLAN routing Problem

    Hi all I have a situation here, I have created some VLANs on a L3 switch(Nortel), no problem with this. Inter vlan routing is taking place over here as well. I have connected this L3 with a 2511 Cisco router. Here I want to mention one thing that all the VLANs can ping the outgoing port of the...

    Pikupiku74220 pointsBadges:
  • Bonding and networking

    I am not a network guy and would like to know how can I setup the below two configurations and its pros and cons. networking component :- WAN: cisco 2970 * 1 Load balancer: F5 switch 1600 * 2 Private subnet: Cisco 2950 * 2 My situation is like that, my F5 switch 1600 will connect to Cisco 2970...

    Frankcheong10 pointsBadges:
  • Unable to Telnet to SCO Unix server

    help please. i recently installed a new cisco router at one of our branches. i am able to ping the head office router and other hosts on the head office lan except the sco unix server. i added a route to the new site in the etc/hosts file but still i cannot telnet or ping the new remote site form...

    Twkays15 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following