Bonding and networking
I am not a network guy and would like to know how can I setup the below two configurations and its pros and cons. networking component :- WAN: cisco 2970 * 1 Load balancer: F5 switch 1600 * 2 Private subnet: Cisco 2950 * 2 My situation is like that, my F5 switch 1600 will [...]
Answer Question
| September 20, 2010 5:34 AM
Cisco, Cisco 2950, Cisco Routers, Cisco switches, Ethernet connection, Linux administration and management, Networking, WAN, Wide Area Networks
I am not a network guy and would like to know how can I setup the below two configurations and its pros and cons. networking component :- WAN: cisco 2970 * 1 Load balancer: F5 switch 1600 * 2 Private subnet: Cisco 2950 * 2 My situation is like that, my F5 switch 1600 will [...]
Answer Question
| September 20, 2010 5:34 AM
Cisco, Cisco 2950, Cisco Routers, Cisco switches, Ethernet connection, Linux administration and management, Networking, WAN, Wide Area Networks
Unable to Telnet to SCO Unix server
help please. i recently installed a new cisco router at one of our branches. i am able to ping the head office router and other hosts on the head office lan except the sco unix server. i added a route to the new site in the etc/hosts file but still i cannot telnet or ping [...]
Answer Question
| September 13, 2010 5:02 AM
Cisco Routers, Routers, Telnet, Telnet protocol, Unix administration, Unix Servers, Wireless in 2010
help please. i recently installed a new cisco router at one of our branches. i am able to ping the head office router and other hosts on the head office lan except the sco unix server. i added a route to the new site in the etc/hosts file but still i cannot telnet or ping [...]
Answer Question
| September 13, 2010 5:02 AM
Cisco Routers, Routers, Telnet, Telnet protocol, Unix administration, Unix Servers, Wireless in 2010
Cisco Router configuration
I would like to know all the configurations and changes that can be done in a router.
Answer Question
| February 9, 2011 12:48 AM
Cisco certifications, Cisco router configuration, Cisco Routers, Router configuration
I would like to know all the configurations and changes that can be done in a router.
Answer Question
| February 9, 2011 12:48 AM
Cisco certifications, Cisco router configuration, Cisco Routers, Router configuration
How to limit max amount of connections per ip on cisco 2811 router
I wish to limit max 100 tcp connections per internal ip address. Thanks
Answer Question
| February 15, 2011 8:46 AM
Cisco 2811, Cisco Routers, Firewalls, IP configuration, Network firewalls, Wireless, Wireless in 2010
I wish to limit max 100 tcp connections per internal ip address. Thanks
Answer Question
| February 15, 2011 8:46 AM
Cisco 2811, Cisco Routers, Firewalls, IP configuration, Network firewalls, Wireless, Wireless in 2010
Can’t enter ROMmon mode in Cisco router 2811
hi i have cisco 2811 router and when i try to enter in rommon mon not possiable i try all but useless on console mod just garabge plese help
Answer Question
| February 22, 2011 4:52 AM
Cisco, Cisco 2800 ROMmon mode, Cisco 2811, Cisco router configuration, Cisco Router Performance, Cisco Routers, Wireless in 2010
hi i have cisco 2811 router and when i try to enter in rommon mon not possiable i try all but useless on console mod just garabge plese help
Answer Question
| February 22, 2011 4:52 AM
Cisco, Cisco 2800 ROMmon mode, Cisco 2811, Cisco router configuration, Cisco Router Performance, Cisco Routers, Wireless in 2010
Are there such things as good reboots on client servers?
IBM has claimed that they have invested billions on their mainframe platform to reduce the need for reboots. EMC and Cisco appear to be doing the same for RAID storage and routers and switches respectively. Yet on client servers reboots are treated as commonplace events. How can both practices co-exists in the same industry. Is [...]
Answer Question
| August 24, 2010 7:25 PM
Cisco, Cisco Routers, Cisco switches, Client server software, EMC, IBM, Open IT Forum, RAID, Server Reboot, Servers
IBM has claimed that they have invested billions on their mainframe platform to reduce the need for reboots. EMC and Cisco appear to be doing the same for RAID storage and routers and switches respectively. Yet on client servers reboots are treated as commonplace events. How can both practices co-exists in the same industry. Is [...]
Answer Question
| August 24, 2010 7:25 PM
Cisco, Cisco Routers, Cisco switches, Client server software, EMC, IBM, Open IT Forum, RAID, Server Reboot, Servers
Block MAC Address on Cisco Aironet 1260 Router
How can I block one mac address from connecting to my Cisco Aironet 1260 Series router? We have open access but one client is being troublesome. Can this be done from the router or is it supposed to be done via the PIX firewall?
Answer Question
| August 23, 2010 6:50 PM
Cisco Aironet, Cisco Aironet 1260, Cisco Routers, Firewalls, MAC address, Wireless in 2010
How can I block one mac address from connecting to my Cisco Aironet 1260 Series router? We have open access but one client is being troublesome. Can this be done from the router or is it supposed to be done via the PIX firewall?
Answer Question
| August 23, 2010 6:50 PM
Cisco Aironet, Cisco Aironet 1260, Cisco Routers, Firewalls, MAC address, Wireless in 2010
How can I configure a connection by pppoe on a Cisco 2600 Router?
please can somebody help me to find out the way i can configure a connection by pppoe on a Cisco 2600 Router?
Answer Question
| August 16, 2010 9:40 AM
Cisco 2600, Cisco Routers, CPE, PPPoE dialer, PuTTY, Windows 7, Wireless in 2010
please can somebody help me to find out the way i can configure a connection by pppoe on a Cisco 2600 Router?
Answer Question
| August 16, 2010 9:40 AM
Cisco 2600, Cisco Routers, CPE, PPPoE dialer, PuTTY, Windows 7, Wireless in 2010
Ports Configuration for 2811 as a Terminal Server
Is there any possible way to disable ports on a Cisco 2811 router that is configured as a terminal server
Answer Question
| August 5, 2010 1:30 AM
Cisco 2811, Cisco 2811 configuration, Cisco router configuration, Cisco Routers, Port configuration, Routers, Terminal Server
Is there any possible way to disable ports on a Cisco 2811 router that is configured as a terminal server
Answer Question
| August 5, 2010 1:30 AM
Cisco 2811, Cisco 2811 configuration, Cisco router configuration, Cisco Routers, Port configuration, Routers, Terminal Server
CISCO vty auto command
A user cannot use show running-config and config terminal using his default permission to my company router after he connects our edge router via telnet using port 23. I have to fix this problem without changing his privilege level. And I have to also solve this issue by using only a single command. any experts [...]
Answer Question
| August 2, 2010 4:41 PM
Cisco IOS, Cisco IOS Commands, Cisco Routers, Routers, Telnet
A user cannot use show running-config and config terminal using his default permission to my company router after he connects our edge router via telnet using port 23. I have to fix this problem without changing his privilege level. And I have to also solve this issue by using only a single command. any experts [...]
Answer Question
| August 2, 2010 4:41 PM
Cisco IOS, Cisco IOS Commands, Cisco Routers, Routers, Telnet
Inter Vlan Routing
Hello. I have 5 vlans working on my network i.e 192.168.80.0, 81.0, 82.0, 83.0, 84.0, 85.0 . i have one core switch where all L2 switches are connected. and router is connected with L2 switch. caz its in another building so cant connect with L3 3750 switch. and i have configured 5 subinterfaces in routers [...]
Answer Question
| August 20, 2010 5:05 PM
Cisco 3750, Cisco Routers, Cisco switches, DHCP, Proxy server, Subinterface, VLAN configuration, Wireless in 2010
Hello. I have 5 vlans working on my network i.e 192.168.80.0, 81.0, 82.0, 83.0, 84.0, 85.0 . i have one core switch where all L2 switches are connected. and router is connected with L2 switch. caz its in another building so cant connect with L3 3750 switch. and i have configured 5 subinterfaces in routers [...]
Answer Question
| August 20, 2010 5:05 PM
Cisco 3750, Cisco Routers, Cisco switches, DHCP, Proxy server, Subinterface, VLAN configuration, Wireless in 2010
Need to configure Bandwidth limiting on per ip basis in cisco router
Hi, Need to configure Bandwidth limiting on per ip basis in cisco router i tried using rate-limit in my [nobr]isp[/nobr] interface using access list 101 If my [nobr]access[/nobr] list is like access-list 101 permit ip any any it’s apply rate-limit to all users when try to apply a single ip access-list 101 permit ip host [...]
Answer Question
| July 26, 2010 2:41 PM
Bandwidth, Bandwidth management, Bandwidth monitoring, Cisco Routers, IP Addresses, Routers
Hi, Need to configure Bandwidth limiting on per ip basis in cisco router i tried using rate-limit in my [nobr]isp[/nobr] interface using access list 101 If my [nobr]access[/nobr] list is like access-list 101 permit ip any any it’s apply rate-limit to all users when try to apply a single ip access-list 101 permit ip host [...]
Answer Question
| July 26, 2010 2:41 PM
Bandwidth, Bandwidth management, Bandwidth monitoring, Cisco Routers, IP Addresses, Routers
cisco 2950 configuration
Hi, I have got a really stupid question to ask. I am running a small wireless internet service, about 20 customers so far. I’m using 4 access points to send out my signal. My input is from a t1 line into a cisco 1841 router. Here is where my problem starts: I’ve been using soho [...]
Answer Question
| November 19, 2011 4:38 AM
Cisco 2950, Cisco router configuration, Cisco Routers, Routers, Wireless in 2010, Wireless routers
Hi, I have got a really stupid question to ask. I am running a small wireless internet service, about 20 customers so far. I’m using 4 access points to send out my signal. My input is from a t1 line into a cisco 1841 router. Here is where my problem starts: I’ve been using soho [...]
Answer Question
| November 19, 2011 4:38 AM
Cisco 2950, Cisco router configuration, Cisco Routers, Routers, Wireless in 2010, Wireless routers
How do I get into the switch portion of a Cisco 2811 if I forgot the password?
How do I get into the switch portion of a Cisco 2811 if I forgot the password
Answer Question
| June 28, 2010 11:38 PM
Cisco 2811 configuration, Cisco router configuration, Cisco Routers, Cisco switches, Network switches
How do I get into the switch portion of a Cisco 2811 if I forgot the password
Answer Question
| June 28, 2010 11:38 PM
Cisco 2811 configuration, Cisco router configuration, Cisco Routers, Cisco switches, Network switches
NAC and Wireless Controllers
I have a need to setup conference rooms that will be used by both corporate and foreign or guest devices. I would like to use wired and wireless for flexibility and video conferencing. NAC seems like a no brainer but am curious if I should look into a Wireless Lan Contoller device of some sort [...]
Answer Question
| July 29, 2010 6:40 PM
Cisco Routers, Cisco Wireless LAN Controller, NAC, Wireless, Wireless LAN controller
I have a need to setup conference rooms that will be used by both corporate and foreign or guest devices. I would like to use wired and wireless for flexibility and video conferencing. NAC seems like a no brainer but am curious if I should look into a Wireless Lan Contoller device of some sort [...]
Answer Question
| July 29, 2010 6:40 PM
Cisco Routers, Cisco Wireless LAN Controller, NAC, Wireless, Wireless LAN controller
cisco 878 and 3com how to get it working and getting access to IP camera via public IP
I got Cisco 878 router with a 3com switch (unmanaged) the end devices Which are connected behind a 3com , are a network recorder and 3 IP camera’s I see the arp and mac address, but I can’t connect to them, or view the camera or able to access the recorder RTR-1# sh arp Protocol [...]
Answer Question
| June 22, 2010 8:49 PM
Cisco 878, Cisco Routers, Network Configuration, Port forwarding, Routers
I got Cisco 878 router with a 3com switch (unmanaged) the end devices Which are connected behind a 3com , are a network recorder and 3 IP camera’s I see the arp and mac address, but I can’t connect to them, or view the camera or able to access the recorder RTR-1# sh arp Protocol [...]
Answer Question
| June 22, 2010 8:49 PM
Cisco 878, Cisco Routers, Network Configuration, Port forwarding, Routers
Routing issue: I want to open SSH
Hi, I would like to get help, I have 2 computers: computer A with 1 network card, IP 172.19.3.22 DG 172.19.3.254 computer B with 2 network cards, ETH0 IP 172.19.35.75 DG 172.19.35.254 ETH1 IP 10.0.0.2 DG 10.0.0.254 Between the computers I have cisco switch with 2 Vlans, Vlan 3 for computer A and Vlan 35 [...]
Answer Question
| June 29, 2010 9:27 AM
Cisco Routers, Cisco switches, Cisco VLAN, Network Configuration, Routers, SSH
Hi, I would like to get help, I have 2 computers: computer A with 1 network card, IP 172.19.3.22 DG 172.19.3.254 computer B with 2 network cards, ETH0 IP 172.19.35.75 DG 172.19.35.254 ETH1 IP 10.0.0.2 DG 10.0.0.254 Between the computers I have cisco switch with 2 Vlans, Vlan 3 for computer A and Vlan 35 [...]
Answer Question
| June 29, 2010 9:27 AM
Cisco Routers, Cisco switches, Cisco VLAN, Network Configuration, Routers, SSH
HSRP use in Two MPLS line
Friend I have mpls line to connectivty from head office to branch office, one live and one backup, now i would like configure HSRP for active active setup. My question is ,right now our backup line is using only redundancy,this line is mpls, if i configure HSRP this line can use another application as well [...]
Answer Question
| November 16, 2011 3:52 AM
CCNP, Cisco Certified Network Professional, Cisco Routers, HSRP, MPLS, Redundant Switches, Routers
Friend I have mpls line to connectivty from head office to branch office, one live and one backup, now i would like configure HSRP for active active setup. My question is ,right now our backup line is using only redundancy,this line is mpls, if i configure HSRP this line can use another application as well [...]
Answer Question
| November 16, 2011 3:52 AM
CCNP, Cisco Certified Network Professional, Cisco Routers, HSRP, MPLS, Redundant Switches, Routers
cisco router 2811 vpn
Hi, is it possible to have both site-to-site and client-to-site vpv on the same interface dialer???
Answer Question
| February 18, 2011 4:58 PM
Cisco 2811, Cisco Routers, Cisco VPN, Routers, VPN design
Hi, is it possible to have both site-to-site and client-to-site vpv on the same interface dialer???
Answer Question
| February 18, 2011 4:58 PM
Cisco 2811, Cisco Routers, Cisco VPN, Routers, VPN design
How to define local bandwidth and international bandwidth on Cisco 3845 with 2960 switch
I have a 1gb local bandwidth with 10mb international bandwidth in my data center. and my problem is i don’t know how to share the international bandwidth equally to my clients. I don’t know if there are device i need to use or is there are anyways i could just control the international bandwidth. The [...]
Answer Question
| February 18, 2011 8:29 PM
Bandwidth management, Cisco 2960, Cisco 3845, Cisco Routers, Routers, Switches
I have a 1gb local bandwidth with 10mb international bandwidth in my data center. and my problem is i don’t know how to share the international bandwidth equally to my clients. I don’t know if there are device i need to use or is there are anyways i could just control the international bandwidth. The [...]
Answer Question
| February 18, 2011 8:29 PM
Bandwidth management, Cisco 2960, Cisco 3845, Cisco Routers, Routers, Switches
