• Configure and deploy network with Cisco 2600 router

    I've tried configuring a router for a network with 98 hosts. I'm using Network Visualiser 4.0 by Routersim. But I'm not getting it done at all. Is there any other means, methods, techniques in configuring routers for such office building network. Or any suggestions on how to configure and deploy...

    LESHTEK5 pointsBadges:
  • Cisco router

    Looking for documentation on configuration. Thanks!

    savman001015 pointsBadges:
  • Cisco IPsec VPN: VPN up but no traffic/ping

    Hi, I'm having some problems setting up an IPsec VPN between a Cisco 851 and a Draytek Vigor 2200E+. The IPsec VPN seems to establish well, passes IPsec phase 2, and shows up as an active IPsec session in both routers. The problem is that I'm unable to ping, or send any traffic, to any of the hosts...

    Synesthesia5 pointsBadges:
  • How to connect two subnets and two isp’s with Cisco RV042G

    I recently bought a Cisco RV042G dual wan router and it served it's primary function of load balancing two internet connections straight out of the box! I was impressed.. Regrettably I hit the limits of my (limited) networking knowledge with the following problems. Let me describe my network first:...

    heijligers15 pointsBadges:
  • RIP, OSPF and EIGRP in same network

    If I have 3 routers connected to gather and every router connect to it one PC I use for first one rip and for second one ospf and for last one eigrp. Its not ping from PC on first netwoke to PC in second or last network why and it ping from router one to second one?

    omar895 pointsBadges:
  • “ip http secure-server ” command is not available

    Hi, I have Cisco 2801 Router, I want to enable https. But "IP http secure-server " command is not available !!!!!? System Version GSHDSL_Router#show version Cisco IOS Software, 2801 Software (C2801-IPBASE-M), Version 15.0(1)M5, RELEASE S OFTWARE (fc2) Technical Support:...

    sam20135 pointsBadges:
  • How to configure Cisco router 2811

    Halo We purchased a Cisco router 2811 with two Ethernet ports: Fast Ethernet 0/0 and Fast Ethernet 0/1, but without WAN interface cards! How can I configure one of the ports to work as a WAN port and the other to act as LAN port, so as to enable the 2811 router exchange information with other...

    1234567tuiojk10 pointsBadges:
  • Cisco 3825 Router

    Can cisco 3825 router support 45mbps link?

    Network Infrastructure5 pointsBadges:
  • Is my router WRT120N still effective?

    I am using CISCO router WRT120N in my Internet Cafe. Now I have a plan to increase the number of computers to 50 PCs. Is my router WRT120N still effective? Note: I don't provide Wifi for clients.

    Markken20 pointsBadges:
  • Cisco2811 common communication failure

    Can somebody please help me out?  I entered a common mode and type confreg 0x1000 with reset on my Cisco 2811 router and since then my router shows nothing but a blank screen with a blinking dash. Anything I type afterwards refuses to respond to commands.  I've done some search on the Internet...

    martix25 pointsBadges:
  • Cisco ACS 3.4

    I have Cisco ACS configured all the routers and switches, but i am not able to login through console port because of policies overridden by the ACS. pelase let me know the command to isolate ACS from the console port.i

    Ekansh400 pointsBadges:
  • Can’t ping servers in our school division after adding cisco 891 routers

    I am currently moving our school network from a flat network to a routed network. There used to be only one DHCP server at the central office that was handing out IP addresses for the entire school division network. The IP range was 172.16.x.x. A router is being added at each site and each site...

    Skenny175 pointsBadges:
  • Cisco layer 3

    what command do we use for a layer 3 switch so it can also act as a router

    Blangco5 pointsBadges:
  • How to route/switch between three different networks/interface through one interface?

    I am trying to setup a network where I am running a client/server test case.  In the middle, it goes through some SUT. Client                           eth0               eth1           Server [120.22.x.x/16] ---------->[Work...

    T0mmy1e15 pointsBadges:
  • Cisco Router 2811 — Load Balance

    I have a cisco 2811 router with two separate HWIC-1FE, i have two ISP links getting into the router and i would like help on configuration on how to balance the links such that if one goes down the other one picks traffic immediately.

    Ruath5 pointsBadges:
  • Router 2811 Port Configuration

    We are trying to use a Cisco 2811 to move data from one segment to another. The Fe0/0 port is configured to 192.9.100.194 (Business Side) and the Fe0/1 is set at 152.52.42.194(test side equipment network). All concentrators and equipment are set to a default-gateway of 192.9.100.250 which is a 6509...

    Jamespcurran5 pointsBadges:
  • how to configure access control list?

    I have problem to understanding how to configure ACL in firewall and cisco router,,so pleas what is the best way to understand ACL and firewall configuration??

    Mohadbazzi47170 pointsBadges:
  • WAN connectivity

    Hi, I had a query regarding WAN connectivity. Can we provide WAN connectivity on ethernet ports(copper as well as fiber)? Because I am assuming to terminate T3/E3 WAN connection from SP on this port to provide 10 Mbos or higher bandwidth. And do this can be provided on branch routers of cisco like...

    Connectivity125 pointsBadges:
  • vb.net telnet

    my job is to telnet a cisco router, pass the credentiials and build configuration. after building the same, i have to search for a line in the config. i want to automate this whole pocess with vb.net. help me

    Hil5 pointsBadges:
  • Network Security – VLANs and APs – Additional Securiy risks?

    Well, I've been kicking this around and thought I'd ask some experts out there. I'm planning on implementing some Wireless Access Points for guestemployee access. The APs will be connected to the core network on VLAN'd ports. I'm wondering about the security issues involved with this beyond the...

    Zeitgeist925 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following