• I want use a D-link Dir-600 router that will sit behind a Cisco router with 2 vlans

    I have an application where I have setup a Cisco 1841 router with 2 vlan connection's, I want to setup a wireless D-link DIR-600 wireless router on one of vlans so visiting venders can get to the internet without being on my network. Do I need to setup the D-Link router with any VLan...

    Shedman35 pointsBadges:
  • 2 DSLs aggregated to a Cisco 5505 asa router

    I am waiting for our FIOS connectivity and am presently using EMBARK DSL in its place. As an interim measure I want to add a second DSL to get more throughput. 1. Can this be done 2. Should both DSL modems ahve the same static ip from the provider Any help would be greatly appreciated Thx - Joe

    Surfsupjoe5 pointsBadges:
  • Commands for binding or mapping Layer 2 data to Layer 3 ports

    I have a question concerning Layer 2 and Layer 3 data on the same device. We have a client that will be sending us Layer 2 data streams, but we have to send them to a device that will only take IP multicasts. We will be using a Cisco 7600 Router with a 6700 Switch Card installed. If this is...

    NetworkingATE1,545 pointsBadges:
  • Cisco Router ips & ids

    what are the commands in ips & ids in cisco router? how to configure

    Kaja20048055 pointsBadges:
  • Cisco 1841

    i have 2 internet connection in company so before its working through proxy server, now need to change via 2 setelight modem - roter - pix - switch so please help me.

    Sunil287865 pointsBadges:
  • SSH configuration on Cisco router

    Please provide me a step to step detail configuration of SSH. Thanks..

    Vinesh123480 pointsBadges:
  • cisco 7961 phone loads

    on a cisco 7961 phone which tftp flash: ............. loads are needed to run on callmanager express on a cisco 3825 router?

    Spc5 pointsBadges:
  • cisco router 1841

    how to install and connect, cisco router 1841 to pc desktop.? how would i know if it is connected.?

    Dustinlr5 pointsBadges:
  • Routers

    What router component holds routing table, ARP cache, and running config file?

    198234765015 pointsBadges:
  • Bandwith for lan segment into wan serials

    I have two cisco 2800 routers, and need to assign diferent bandwith to diferent lans, that send data into these two equipments, what is the best form to config this?

    Gdavila5 pointsBadges:
  • Loadbalancing & Failover

    We have to location A & B, between location we have two 2 mbps ethernet converted leased line, now we are going to update one line to 4 mbps also want to configure Loadbalancing & automatic failover in case of any line fails. Please suggest better solution & cisco router to achive this.

    Rakeshjp5 pointsBadges:
  • how do i check part number for cisco 2821

    router 2821

    Ha25 pointsBadges:
  • Cisco Wireless 1200 DHCP Issues

    Ok, I have seen this same issue on several message boards etc. but I have yet to find a good answer so here it goes. I have a network with 12 Cisco 1200 series access points all connecting to 3550PWR switches. The switches are configured with 2 vlans, one for a public wireless LAN and the other as...

    Leeth70 pointsBadges:
  • Locking the IP address to the MAC address

    Hi all.... Aim: Ip address lets say when assigned to a particular MAC let it be pc, should not be used by any other mac, even if i switch off the device. I tried through dhcp reservation option which maps the ip address to a mac address, it works. but the problem is, when i switch off the...

    Mohdanwarahmed15 pointsBadges:
  • Cisco routing problem

    I have a Cisco router (routerA) at a remote site, which connects point-to-point to the HQ site (routerB), and it needs to communicate to another router (routerC) that is connected at the HQ site. From the CLI in routerA I cannot ping routerC, but from a PC located with routerA, I can open a dos...

    Jdleon85 pointsBadges:
  • Cisco 2811 VLAN Usage

    I inherited a network that has a Cisco 2811 router setup with the following: interface FastEthernet0/0 no ip address no ip route-cache cef no ip route-cache duplex full speed 100 ! interface FastEthernet0/0.18 description Data VLAN encapsulation dot1Q 18 native ip address

    Zwitter1535 pointsBadges:
  • Cisco: Setting a VLAN across a network

    hi,newbie here :) I am working on Packet Tracer 5.0 and I want to setup 2 vlan's that spread across a network. I attach the view of the network: 2 of 3 hosts on switch 1 belong in vlan10 and the other one belongs to vlan20. Likewise, 2 of 3 hosts on switch 2 belong to vlan10 and the other one...

    Teo20 pointsBadges:
  • 2811 router

    sending a fax and stay connected on 40 sec then drops. Can this be an opt missing?

    Jai4305 pointsBadges:
  • iipsec vpn between cisco routers, using dsl modem(NAT ROUTER)

    Hi, I have two office and both office have broadband connection. I would like to know how to connect these sites using (ipsec vpn ) cisco routers through dsl modem connection.Both offices have static IP. I have lab experience in configuring site to site ipsec VPN. Now I am confused about applying...

    Puli45 pointsBadges:
  • QoS on my cisco 3620 router for my VoiP traffic

    I am wanting to enable QoS on my cisco 3620 router for my VoiP traffic. I believe this can be done using ACL's instead of SDM. Does anyone have any info?.

    ITKE376,290 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.