• Cisco router 2811 ipv6 configuration

    hi, can someone help me out how to configure ipv6 on fastethernet n serial interface? thanks.

    Vm8185 pointsBadges:
  • how to reduce high CPU and memory utilization

    please suggest me , is there any set of command to reduce high CPU and memory utilization of cisco router

    Vinesh123480 pointsBadges:
  • Remove running configuration in Cisco routers and switches

    How do I remove running configuration in Cisco routers and switches? I tried to run erase config/all, erase flash: nvram etc but it does not work. I want to erase all running config in devices. Can anybody help me?

    Ekansh400 pointsBadges:
  • Cisco 1941, Cisco 1921, Maintaining Top in Cisco 1900 Series?

    What are top advantages of Cisco 1900 series? Cisco 1941? or Cisco 1921? Better for enterprise...

    donglee65 pointsBadges:
  • Can’t enter ROMmon mode in Cisco router 2811

    hi i have cisco 2811 router and when i try to enter in rommon mon not possiable i try all but useless on console mod just garabge plese help

    Alca5 pointsBadges:
  • How to Connect Branch Office?

    We recently initiated a branch office setup in the same city. (Setup is still in process) Currently in Main branch we are using Cisco 2800 series router and Cisco 6500 series Core Switches. Similarly in Branch Office, we have one Cisco 2800 series router and some POE switches. In order to connect...

    Makmaniax15 pointsBadges:
  • HSRP use in Two MPLS line

    Friend I have MPLS line to connect from head office to branch office, one live and one backup. Now, I would like configure HSRP for active setup. My question is: Right now, our backup line is using only redundancy. This line is MPLS. If I configure HSRP, this line can use another application as...

    Hiren5 pointsBadges:
  • Configure IP SLA

    How to configure IP SLA using two routers?

    Tkp5 pointsBadges:
  • How to configure two Cisco 2600 routers

    Hi, we have two Cisco 2600 routers, one deployed in our main office and the other in our remote site. We also have two DSL connections. We have our Exchange server in main office. Q1. How to configure the two router to use the 2 DSL connections that we have? Q2. How to route our exchange server to...

    Killerj5 pointsBadges:
  • Configure and deploy network with Cisco 2600 router

    I've tried configuring a router for a network with 98 hosts. I'm using Network Visualiser 4.0 by Routersim. But I'm not getting it done at all. Is there any other means, methods, techniques in configuring routers for such office building network. Or any suggestions on how to configure and deploy...

    LESHTEK5 pointsBadges:
  • Cisco router

    Looking for documentation on configuration. Thanks!

    savman001015 pointsBadges:
  • Cisco IPsec VPN: VPN up but no traffic/ping

    Hi, I'm having some problems setting up an IPsec VPN between a Cisco 851 and a Draytek Vigor 2200E+. The IPsec VPN seems to establish well, passes IPsec phase 2, and shows up as an active IPsec session in both routers. The problem is that I'm unable to ping, or send any traffic, to any of the hosts...

    Synesthesia5 pointsBadges:
  • Cisco2811 common communication failure

    Can somebody please help me out?  I entered a common mode and type confreg 0x1000 with reset on my Cisco 2811 router and since then my router shows nothing but a blank screen with a blinking dash. Anything I type afterwards refuses to respond to commands.  I've done some search on the Internet...

    martix25 pointsBadges:
  • Can’t ping servers in our school division after adding cisco 891 routers

    I am currently moving our school network from a flat network to a routed network. There used to be only one DHCP server at the central office that was handing out IP addresses for the entire school division network. The IP range was 172.16.x.x. A router is being added at each site and each site...

    Skenny175 pointsBadges:
  • How to route/switch between three different networks/interface through one interface?

    I am trying to setup a network where I am running a client/server test case.  In the middle, it goes through some SUT. Client                           eth0               eth1           Server [120.22.x.x/16] ---------->[Work...

    T0mmy1e15 pointsBadges:
  • Cisco Router 2811 — Load Balance

    I have a cisco 2811 router with two separate HWIC-1FE, i have two ISP links getting into the router and i would like help on configuration on how to balance the links such that if one goes down the other one picks traffic immediately.

    Ruath5 pointsBadges:
  • Router 2811 Port Configuration

    We are trying to use a Cisco 2811 to move data from one segment to another. The Fe0/0 port is configured to 192.9.100.194 (Business Side) and the Fe0/1 is set at 152.52.42.194(test side equipment network). All concentrators and equipment are set to a default-gateway of 192.9.100.250 which is a 6509...

    Jamespcurran5 pointsBadges:
  • how to configure access control list?

    I have problem to understanding how to configure ACL in firewall and cisco router,,so pleas what is the best way to understand ACL and firewall configuration??

    Mohadbazzi47170 pointsBadges:
  • Cisco 1841,SDM will not connect nor install

    I am trying to install a VPN Server on my Cisco 1841 router. When I try to connect SDM it will not connect. I tried reinstalling the SDM on the router, but it comes to a stage & says "copy operation failed". I tried to install VPN through CLI, but the CLI doesn't recognize the CRYPTO command. Need...

    Aslamalikhan25 pointsBadges:
  • Cisco Router 2800 series step by step configuration using DSL

    can you please provide me step by step configuration how to connect/use DSL connection for Cisco Router 2800 series. i want to use DSL as backup in case T1 is down.

    Erwin5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following