Cisco Router Configuration

what this command means in 1841 router config

what this command means in 1841 router config "ip admission max-nodata-conns 3" Software/Hardware used: 1841

d-link switch to cisco router

how can I include 3 ip addresses in a single fast ethernet port of a cisco router if the switch connected to that port is a d-link switch? do i have to create subinterface on that fast ethernet port?  

configuration of auxilary port for cisco router

Hi, We need to configure a adapter for third party. vendor need to login via pstn thorugh this router. i can configure the cisco fax adopter but i dont know how vendor will login to this router please explain. can any body describe what is the scenario "login through aux port via pstn line" ...

Will a crossover cable connect these routers?

will a crossover cable connect these routers?? Software/Hardware used: cisco 2611 routers

Cisco 2811 - Divide Bandwidth

We have Cisco 2811 router with on serial interface and four fast ethernets. We planned to take 10 mbps Internet leased line and we have to divide it into two parts. For one network is should be 6 Mbps and the rest bandwidth for another network. Can any help in this Software/Hardware used: cisco...

Cisco 2600 Router and Two ISP

How can configure two Internet LL (Primary and backup)on same cisco router 2600 (2 Serieal and 4 ethernet ports). ISP 1 - 4Mbpes and ISP 2 - 1 Mbps. Software/Hardware used: cisco Router 2600 with 2 serial and 4 ethernet ports

how can we configure a 36 port router?

how to install, configure and use a cisco 36 port router? Software/Hardware used: cisco 36 port router

trusted and untrusted interface

what is the meaning of trusted and untrusted interface in security configuration in cisco router? Software/Hardware used: software

Cisco 2811 ccme config

Hi guys, I have two Cisco 2811 routers. Each of them has 2 Fast Ethernet and 4 7960 ip phone. i need to set it up for lab purposes. how do i configure this?

how to delete router configuration

I have 2800 router and i tried to delete the all old configuration but its not deleted,any idea about this problem Software/Hardware used: hardware

WCCP step by step setup and utilisation of Cisco Cache engine or Baracuda

I am new to this field and would like assistance of setting up WCCP on a Router and two content engines, Baracuda and cisco Cache engine. Please help? Software/Hardware used: Cisco Router, Cache engine, and Baracuda chache engine

how to configure PA-MC-STM1 card in cisco 7206 router

I want to know how to configure PA-MC-STM1  card in cisco 7206 router Software/Hardware used: Cisco 7206 Router

cisco router 1841

how to install and connect, cisco router 1841 to pc desktop.? how would i know if it is connected.?

Bandwith for lan segment into wan serials

I have two cisco 2800 routers, and need to assign diferent bandwith to diferent lans, that send data into these two equipments, what is the best form to config this?

network problem

Hi expert, i have to connect a router with another another with router by E1 transmission .i have cisco 2800 series but in my router in CLI prompt i cannot find controller, interface serial but only fasethernet and Multilink .how could i connect this router

Cisco routing problem

I have a Cisco router (routerA) at a remote site, which connects point-to-point to the HQ site (routerB), and it needs to communicate to another router (routerC) that is connected at the HQ site. From the CLI in routerA I cannot ping routerC, but from a PC located with routerA, I can open a dos...

Cisco Networking

How can we provide load sharing on single router of two ISPs. plz let us suggest on the same.

BGP setting in Cisco 2811 router

how to configure bgp in cisco 2811

Two routers configration

I have configured two routers completly the two router connected by them serial, router 1 can bing to interface e 0 and s 0 of router 2 and router 2 can ping interfaces e 0 an s0 of router 1 but network on e 0 of router 1 cannt bing s0 of router 2 and inverse right what is the problem

SSH configuration on Cisco router

Please provide me a step to step detail configuration of SSH. Thanks..