Fortinet Firewall in transparent mode over VLAN Trunk 802.1Q
We have a fortigate firewall in transparent mode. WAN interface is on VLAN 10 and INTERNAL interface is on VLAN 20. If I connect a server behind VLAN 20 on the switch where the firewall is connected everything works fine. The problem is when I connect to another switch that is getting VLAN 20 over [...]

Answer Question   |  February 28, 2012  9:11 PM
Cisco 3550, FortiGate, transparent mode, VLAN

enable adjacency
How do I enable the adjacency feature on a cisco 3550

Answer Question   |  July 6, 2010  4:05 PM
Cisco, Cisco 3550, Features/Functionality

Routing of traffic between separate compainies both using private 10 net addresses
We have two different networks in two towns that wish you route traffic using existing 10.x.x.x network traffic. There is no conflict with the addresses we wish to use. There is of course a firwall in place on both sides. Is it possible to route all 10 net traffic between sights using one VPN, or [...]

Answer Question   |  July 6, 2010  8:03 PM
Cisco 3550, Cisco VPN, Firewall Cluster, Private IP, VPN issue

bandwith management for Cisco 3550
how can i split my banwidth per port with 3550 cisco?

Answer Question   |  March 23, 2010  9:15 AM
Bandwidth management, Catalyst Switches, Cisco 3550, Cisco Catalyst 3550, Switches

Combining Networks with Same IP Scheme, VLAN,
Hi, We are combining an couple offices next week & i need some advice. The networks already have VLANs set up. we have a Cisco 3550 Layer 3 switch set up to route traffic. The servers are on this site also. The network IP’s are 10.1.1.x, 10.1.4.x & 10.1.5.x. Servers reside on all of those [...]

Answer Question   |  November 16, 2009  4:12 PM
ASA, Cisco 3550, LAN, Network Configuration, Network management, Network Topology, PIX, PIX 506e, PIX 515E, VLAN, VPN, WAN

how many vlan create in cisco switch
how many vlan created in cisco 3550 & 3750 switch

Answer Question   |  July 30, 2009  5:33 AM
Cisco 3550, cisco 3750 switch stack configuration, Stack Configuration, Switches, VLAN

How to rate limit on Cisco Catalyst 3550-EMI
Hello, I have a cisco switch 3550 EMI and I need to do rate limiting on ethernet ports. class-map match-all 5M description 5M with 500K burst ! policy-map 5M class 5M police 5120000 51200 exceed-action drop interface FastEthernet0/3 switchport access vlan 100 switchport mode dynamic desirable speed 100 duplex full service-policy input 5M service-policy output [...]

Answer Question   |  March 2, 2009  12:48 AM
Bandwidth limits, Bandwidth management, Cisco, Cisco 3550, Cisco Catalyst 3550, Cisco Catalyst 3550-EMI, Cisco switch configuration, Switch configuration, Switches

Cisco 3550 config assistance needed
Here is the network scenario: I have two T1′s coming into our main building. One is a p2p T1 circuit to a remote office. The other is a basic T1 circuit for Internet connectivity. The far end of the p2p is in the 192.168.3.0 255.255.255.0 network. The local router is an Adtran with an IP [...]

Answer Question   |  March 1, 2009  7:53 PM
Cisco, Cisco 3550, Cisco switches, Layer 3 switch

Cisco 3550 Failover
Hi, I am wondering if there is any failover (active- active or active-passive) solution for 3550 switches. I just would like to sync configurations of two 3550 as backup of each other. Thank you for your time in reading/responding my question. Emre.

Answer Question   |  November 15, 2008  9:08 AM
Cisco 3550, Cisco 3550 failover, Cisco Catalyst 3550, Cisco switches, Switches

Bandwidth Limit on Cisco 3550 catalyst switch on Fast ethernet
Dear friend, I have a cisco 3350 catalyst switch, I want to limit bandith on that interface to 64kbps, I need help on this. I need to know another way of limiting the bandwith using access list on the ip address assigned to the host on that interface. send your replty to raj_741976@sify.com

Answer Question   |  November 20, 2008  11:31 AM
64 kbps, Bandwidth management, Cisco 3550, Cisco switches, Switches