• Connect Cisco 2800 to 2 ISPs, and internal networks through switch module.

    Greetings.. I am considering what equipment I need for my project. I have to load balance between two connections to the same ISP. The question I have is simply, if I can use a Cisco 2811 router, using the fa0/0 - 1 to connect to the ISP and use the internal switch module for my networks ? I have...

    Netsmurf5 pointsBadges:
  • Cisco 2811 – Divide Bandwidth

    We have Cisco 2811 router with on serial interface and two fast ethernets. We planned to take 1 mbps leased line and we have to divide it into two parts. For one network is should be 300 kbps and the rest bandwidth for another network. Can any help in this.

    PSKR20 pointsBadges:
  • Cisco 2811 config

    Hi guys, I have two Cisco 2811 routers. Each of them has 2 Fast Ethernet and 1 Serial interfaces. I have two WAN connections on each router. One of them via FastEthernet0/0 and another one via Serial. I try to connect these two routers with redundancy scheme. For example, if primary connection...

    Fds19895 pointsBadges:
  • Share two broadbanc connections in 2811 router

    I am having a 2811 router with one Serial interface and two Fe. We have two broadband connections. Can any one help how to configure router with these specifications. Thanks in advance

    PSKR20 pointsBadges:
  • Cable required – Cisco 2811

    I need to know the type of cable to login to cisco 2811 router. Can i use the LAN port on my laptop, use a straight cable and connect through the console port of the router? Please help

    Naveenkm135 pointsBadges:
  • Cisco 2811 Power Supply Jumper – PS Type

    I have replaced a DC supply with an AC 100V but the new power supply doesn not havbe anywhere for the PS Type Jumper connection. What does the PS Type do and can I operate without that connected (as the new power supply has no connector) ? Thanks in Advance.

    Greencj35 pointsBadges:
  • Cisco 2811 PVDM2-24DM Initialising

    Dear All Professionals, We have taken on the installation of a Cisco 2811 to make digital communications over ISDN and are requiring assistance with our hardware configuration . We have all the necessary modules and so on however our current problem is: We have the digital modem module in slot 0...

    Jtrade5 pointsBadges:
  • load balance on WAN interfaces

    How can I set up two 2811 routers coneected together with two leased lines with load balance. There are two 2M leased lines to form a 4M leased line for operation.

    Cmcheng5 pointsBadges:
  • 4 VLANS, 3 locations, 3 Routers, No communication between Lans or VLANs

    OK, here is my problem, I'm working on a project in the Test phase right now. I have 3 routers (Cisco 2811s), all running EIGRP, these are seperating 3 goegraphical regions. Each of these Routers is linked via Trunking line to a Switch which has 4 VLANs enable. According to everything I have found...

    CRagsdale32755 pointsBadges:
  • How to add a subinterface in Cisco 2811 router

    how to add a subinterface in router 2811

    Fsheb5 pointsBadges:
  • Cisco 2811 router with Ethernet access to MPLS

    Can a Cisco 2811 router support a 40Mbps MPLS connection using Fast Ethernet access?

    Webonauta15 pointsBadges:
  • Configure 2 lease line on Same router 2811

    Hi All, Currently we are having 1 lease line in our office and soon we are going to have another lease line as backup from other service provider,now the thing is if the provider of the lease line is same then it will be very easy for mr to configure it becoz of same publice ip..but now it becomes...

    Deveshbais10 pointsBadges:
  • Cannot access Cisco 2811 web interface

    Hello, I am able to SSH in to the device, however the web interface will not accept the same credentials. I know nothing about Cisco, and this unit will be replaced soon so I just need to get a few things off of it before it goes on the shelf. What I need are all of the MAC addresses in one of the...

    Tbarth5 pointsBadges:
  • Cisco 2811 router and need to create a VPN

    I have a Cisco 2811 router and need to create a VPN to another site but not sure what their endpoint device is. What I am looking for is a white paper on how to configure the Cisco router for a VPN. Can anyone help me?

    Cyberref5 pointsBadges:
  • DSL service to 2811 router

    Can a DSL service provide voice to Cisco 7961 phones through a 2811 router?

    DGJ5 pointsBadges:
  • CISCO 2811 ETHERNET CONFIGURATION

    I am using CISCO 2811 router. This CISCO router has a LAN connected via a switch on one side and the ISP via a fibre on the other end. The router looses internet connection periodically, up to seven (7) times every day and this interrupts office work. when I shut down ethernet zero (0) and bring it...

    Gentle5 pointsBadges:
  • CISCO 2811 Scalability

    I have a CISCO2811 Router with two Fast Eth ports. Whether I can add one more module. Whether I can have a bandwidth of 8Mbps WAN in one of my Fast Eth ports. Whether I can balnce two ISPs in this CISCO 2811

    Mss5 pointsBadges:
  • Cisco Router 2811 with VWIC 2MFT G703 Cards

    MY CEO have provided my the cisco 2811 with vwic 2mft g703 installed in it, is there any person who could give me the step by step instrauction to configre this router, this is my first time to configure router from scrap.

    Techartist20 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following