Cisco Network
I am using Cisco Packet Tracer 5.2 for study, it seem to be good. I have configure Intervaln routing on 3 coreswitches which is workign fine with vast topology. I tried to place one router 2811 as a firewall between my wan and lan. But i am not able to ping from router to core [...]

Answer Question   |  January 6, 2010  4:37 AM
Cisco 2811, Cisco 3560, Cisco networks, Cisco Packet Tracer, InterVLAN, InterVLAN Routing

How do you get the VLAN protocol to go up?
I’ve forgotten some information on VLAN protocols. I am butting my head against the wall right now trying to get the VLANs on my Cisco 2811 router to change to up/up from up/down. Does anyone know how to get the protocol of a VLAN to go “up”? I’m just plain forgetting it all right now.

Answer Question   |  February 18, 2011  8:10 PM
Cisco 2811, Cisco Routers, Routers, VLAN, VLAN Trunking Protocol

Cisco 2811 – Divide Bandwidth
We have Cisco 2811 router with on serial interface and four fast ethernets. We planned to take 10 mbps Internet leased line and we have to divide it into two parts. For one network is should be 6 Mbps and the rest bandwidth for another network. Can any help in this

Answer Question   |  October 5, 2009  8:54 AM
Bandwidth management, Cisco 2811, Cisco router configuration, Router configuration

Console Session on cisco router
Hi                I have two routers in my lab , which  is not accessible via console. one is a cisco 3640 router, it shows some unrecognised characters when accessing via console. i did reset the baud rate jumper ,but no result.               In 2811 router it shows boot up [...]

Answer Question   |  September 15, 2009  6:31 AM
Cisco 2811, Cisco 3640, Cisco Console Port, Cisco Routers

VPN SITE TO SITE CONFIGURATION
This is my first time to configure site to site vpn from ASA5510:116.93.65.34 -Host-to REmote Cisco 2811-41.204.36.150 (LAN-IP Start at 172.16.16.0-172.16.19.254 subnet mask-255.255.252.0) Note: Already done configruation on ASA5510 but need to start configure on cisco2811 but i dont know the cli and where to start Just configure site to site VPN under ASA5510 and [...]

Answer Question   |  June 25, 2012  9:15 AM
Cisco 2811, CLI, VPN configuration

BGP setting in Cisco 2811 router
how to configure bgp in cisco 2811

Answer Question   |  June 9, 2009  3:45 AM
BGP, Border Gateway Protocol, Cisco 2811, Cisco router configuration, Router configuration, Routers

2811 router
sending a fax and stay connected on 40 sec then drops. Can this be an opt missing?

Answer Question   |  June 3, 2009  2:05 PM
Cisco 2811, Cisco Routers, Fax and print management

Cisco 2811 Fast Ethernet and LAN configuration
i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

Answer Question   |  October 5, 2009  4:42 AM
Cisco, Cisco 2811, Cisco router configuration, Cisco Routers, Fast Ethernet, LAN configuration, Router configuration, Routers

Cisco 2811 – Divide Bandwidth
We have Cisco 2811 router with on serial interface and two fast ethernets. We planned to take 1 mbps leased line and we have to divide it into two parts. For one network is should be 300 kbps and the rest bandwidth for another network. Can any help in this.

Answer Question   |  May 12, 2009  9:01 AM
Bandwidth, Bandwidth management, Cisco 2811, Cisco router configuration, Cisco Routers, Leased line, Network design, Router configuration, Routers

Cisco 2811 config
Hi guys, I have two Cisco 2811 routers. Each of them has 2 Fast Ethernet and 1 Serial interfaces. I have two WAN connections on each router. One of them via FastEthernet0/0 and another one via Serial. I try to connect these two routers with redundancy scheme. For example, if primary connection Serial is down [...]

Answer Question   |  May 4, 2009  1:40 PM
Cisco 2811, Cisco 2811 configuration, Cisco Routers, Remote connection, Routers, VPN, WAN

Cable required – Cisco 2811
I need to know the type of cable to login to cisco 2811 router. Can i use the LAN port on my laptop, use a straight cable and connect through the console port of the router? Please help

Answer Question   |  April 14, 2009  11:17 AM
Cables, Cabling, Cisco 2811, Cisco Console Port, Cisco Routers, Routers

Share two broadbanc connections in 2811 router
I am having a 2811 router with one Serial interface and two Fe. We have two broadband connections. Can any one help how to configure router with these specifications. Thanks in advance

Answer Question   |  April 15, 2009  7:05 AM
Broadband, Cisco 2811, Cisco router configuration, Cisco Routers

Cisco 2811 configuration for managing traffic through two Internet connections
Cisco 2811 configuration for managing traffic through two Internet connections

Answer Question   |  March 4, 2009  9:08 PM
Cisco 2811, Cisco 2811 configuration, Network traffic management

Cisco 2811 configuration for managing traffic through two Internet connections
Hi all, I have one cisco 2811 router with serial interface for leased line connection ton internet and an adsl wic for Internet connexion too. What I what is to let http traffic goes through the adsl connexion and other trafic goes through the leased line. IS it possible and how? Thanks

Answer Question   |  June 12, 2009  7:51 AM
ADSL, Cisco, Cisco 2811, Cisco 2811 configuration, Cisco ADSL WIC, Cisco router configuration, Leased line management, Router configuration, Routers

Cisco 2811 PVDM2-24DM Initialising
Dear All Professionals, We have taken on the installation of a Cisco 2811 to make digital communications over ISDN and are requiring assistance with our hardware configuration . We have all the necessary modules and so on however our current problem is: We have the digital modem module in slot 0 and do not see [...]

Answer Question   |  February 27, 2009  9:40 AM
Cisco, Cisco 2811, Cisco 2811 configuration, Cisco 2811 Integrated Services Router, Cisco 2811 PVDM2-24DM, Cisco router configuration, Router configuration, Routers

load balance on WAN interfaces
How can I set up two 2811 routers coneected together with two leased lines with load balance. There are two 2M leased lines to form a 4M leased line for operation.

Answer Question   |  February 9, 2009  3:52 PM
Cisco 2811, Cisco router configuration, Cisco Routers, Load balancing, WAN

Cisco 2811 Power Supply Jumper – PS Type
I have replaced a DC supply with an AC 100V but the new power supply doesn not havbe anywhere for the PS Type Jumper connection. What does the PS Type do and can I operate without that connected (as the new power supply has no connector) ? Thanks in Advance.

Answer Question   |  February 27, 2009  12:28 PM
Cisco, Cisco 2811, Cisco 2811 Integrated Services Router, Cisco Routers, Router power supply, Routers

4 VLANS, 3 locations, 3 Routers, No communication between Lans or VLANs
OK, here is my problem, I’m working on a project in the Test phase right now. I have 3 routers (Cisco 2811s), all running EIGRP, these are seperating 3 goegraphical regions. Each of these Routers is linked via Trunking line to a Switch which has 4 VLANs enable. According to everything I have found in [...]

Answer Question   |  December 16, 2008  5:54 PM
Cisco 2811, Cisco Routers, Networking, Routers, Routing protocols, Switches, Trunking, VLAN

How to add a subinterface in Cisco 2811 router
how to add a subinterface in router 2811

Answer Question   |  December 4, 2008  12:58 PM
Cisco, Cisco 2811, Cisco IOS, Cisco Routers, Cisco subinterface configuration, Router configuration, Routers, Subinterface, Subinterface configuration

Cisco 2811 router with Ethernet access to MPLS
Can a Cisco 2811 router support a 40Mbps MPLS connection using Fast Ethernet access?

Answer Question   |  November 21, 2008  11:55 PM
Cisco 2811, Cisco Routers, Ethernet, Fast Ethernet, MPLS, Multiprotocol Label Switching, Router configuration, Routers