Cisco 2811

How do you get the VLAN protocol to go up?

I've forgotten some information on VLAN protocols. I am butting my head against the wall right now trying to get the VLANs on my Cisco 2811 router to change to up/up from up/down. Does anyone know how to get the protocol of a VLAN to go "up"? I'm just plain forgetting it all right now. ...

Cisco 2811 - Divide Bandwidth

We have Cisco 2811 router with on serial interface and four fast ethernets. We planned to take 10 mbps Internet leased line and we have to divide it into two parts. For one network is should be 6 Mbps and the rest bandwidth for another network. Can any help in this Software/Hardware used: cisco...

Console Session on cisco router

Hi                I have two routers in my lab , which  is not accessible via console. one is a cisco 3640 router, it shows some unrecognised characters when accessing via console. i did reset the baud rate jumper ,but no result.               In 2811 router it shows boot...

VPN SITE TO SITE CONFIGURATION

This is my first time to configure site to site vpn from ASA5510:116.93.65.34 -Host-to REmote Cisco 2811-41.204.36.150 (LAN-IP Start at 172.16.16.0-172.16.19.254 subnet mask-255.255.252.0) Note: Already done configruation on ASA5510 but need to start configure on cisco2811 but i dont know the cli...

BGP setting in Cisco 2811 router

how to configure bgp in cisco 2811

2811 router

sending a fax and stay connected on 40 sec then drops. Can this be an opt missing?

Cisco 2811 Fast Ethernet and LAN configuration

i have cisco2811 router and i want to configure its 2 fast ethernet on my isp and PC or lan. can someone with a good heart to help me what command i will use on configuration level on both router and lan to have an internet connection.

Cisco 2811 - Divide Bandwidth

We have Cisco 2811 router with on serial interface and two fast ethernets. We planned to take 1 mbps leased line and we have to divide it into two parts. For one network is should be 300 kbps and the rest bandwidth for another network. Can any help in this.

Cisco 2811 config

Hi guys, I have two Cisco 2811 routers. Each of them has 2 Fast Ethernet and 1 Serial interfaces. I have two WAN connections on each router. One of them via FastEthernet0/0 and another one via Serial. I try to connect these two routers with redundancy scheme. For example, if primary connection...

Cable required - Cisco 2811

I need to know the type of cable to login to cisco 2811 router. Can i use the LAN port on my laptop, use a straight cable and connect through the console port of the router? Please help

Share two broadbanc connections in 2811 router

I am having a 2811 router with one Serial interface and two Fe. We have two broadband connections. Can any one help how to configure router with these specifications. Thanks in advance

Cisco 2811 configuration for managing traffic through two Internet connections

Cisco 2811 configuration for managing traffic through two Internet connections

Cisco 2811 configuration for managing traffic through two Internet connections

Hi all, I have one cisco 2811 router with serial interface for leased line connection ton internet and an adsl wic for Internet connexion too. What I what is to let http traffic goes through the adsl connexion and other trafic goes through the leased line. IS it possible and how? Thanks

Cisco 2811 PVDM2-24DM Initialising

Dear All Professionals, We have taken on the installation of a Cisco 2811 to make digital communications over ISDN and are requiring assistance with our hardware configuration . We have all the necessary modules and so on however our current problem is: We have the digital modem module in slot 0...

load balance on WAN interfaces

How can I set up two 2811 routers coneected together with two leased lines with load balance. There are two 2M leased lines to form a 4M leased line for operation.

Cisco 2811 Power Supply Jumper - PS Type

I have replaced a DC supply with an AC 100V but the new power supply doesn not havbe anywhere for the PS Type Jumper connection. What does the PS Type do and can I operate without that connected (as the new power supply has no connector) ? Thanks in Advance.

4 VLANS, 3 locations, 3 Routers, No communication between Lans or VLANs

OK, here is my problem, I'm working on a project in the Test phase right now. I have 3 routers (Cisco 2811s), all running EIGRP, these are seperating 3 goegraphical regions. Each of these Routers is linked via Trunking line to a Switch which has 4 VLANs enable. According to everything I have...

How to add a subinterface in Cisco 2811 router

how to add a subinterface in router 2811

Cisco 2811 router with Ethernet access to MPLS

Can a Cisco 2811 router support a 40Mbps MPLS connection using Fast Ethernet access?

Configure 2 lease line on Same router 2811

Hi All, Currently we are having 1 lease line in our office and soon we are going to have another lease line as backup from other service provider,now the thing is if the provider of the lease line is same then it will be very easy for mr to configure it becoz of same publice ip..but now it...