1
  • Cisco Easy VPN Problems Nat outside on Static IP

    Thanks in advance for any clues, direction or help!!! My problem is that I can’t get my Easy VPN up and running!!  I get an error from my iPad saying “The VPN Server did not respond” I think that the issue is that I don’t know how to set up the WAN - interface to accept VPN request and get...

    larsarler5 pointsBadges:
  • Cisco router 2811 ipv6 configuration

    hi, can someone help me out how to configure ipv6 on fastethernet n serial interface? thanks.

    Vm8185 pointsBadges:
  • Cisco 2811 configuration for managing HTTP and other traffic through two connections

    Hi all, I have one Cisco 2811 router with serial interface for leased line connection to internet and an adsl wic for Internet connection too. What I what is to do is let HTTP traffic goes through the adsl connexion and other traffic go through the leased line. Is it possible and how? Thanks

    AKN15 pointsBadges:
  • Cisco 2811 configuration for managing traffic through two Internet connections

    How can I use a Cisco 2811 configuration for managing traffic through two Internet connections?

    Alcisoft5 pointsBadges:
  • Cisco 2811 – 3 VLAN

    I have a Cisco 2811 Router with 3VLANs. I reset the router from scratch and want to set up my EtherSwitch with 16 ports to have 3 VLANS. Ports 1-10 to be VLAN1, 11-14 to be VLAN2, and 14-16 to be VLAN3. The Gig port will be for my hardware firewall that then goes to my modem. So: Modem -> HW...

    SomEntity5 pointsBadges:
  • LDAP server configuration

    I need help setting up the Bind statement on the LDAP server config on my 2811 router

    Dlamar5 pointsBadges:
  • Router 2811 Port Configuration

    We are trying to use a Cisco 2811 to move data from one segment to another. The Fe0/0 port is configured to 192.9.100.194 (Business Side) and the Fe0/1 is set at 152.52.42.194(test side equipment network). All concentrators and equipment are set to a default-gateway of 192.9.100.250 which is a 6509...

    Jamespcurran5 pointsBadges:
  • Transfer config of cisco 2811

    I have a new cisco 2811 and need to replace the old 2811. I have all the cables but do not know how to proced. Please help me.... Thank you

    Daniel20075 pointsBadges:
  • Cisco 2811 routing question!

    Ok this is on odd problem i have a set of ip's that are supplied by our transit provider one is the primary IP address the others are seperate DMZ ip's. The router i need to basically allow the range though the router.  I dont have much experience with Cisco so any help would be fanstastic! 

    RhodriRoss5 pointsBadges:
  • How do I bond 2 T1 together usinig a Cisco 2811?

    How do I bond 2 T1 together usinig a Cisco 2811?

    Rjratcli5 pointsBadges:
  • VPN Configuration

    could anyone help me how to configuring vpn?

    Hangsiput15 pointsBadges:
  • VOIP over leased line

    Can we run Voip over leased line instead of PRI

    Ekansh400 pointsBadges:
  • Call Divert to Mobile for non UCCM User using Cisco Voice Gateway

    Hi, I have a requirement for a DDI number to be on permanent divert to a mobile.  The user does not have a account on the call manager, nor does he need one.  I just need to provide a Land-line number so it can divert to his mobile.  What is the best way for me to achieve this with the lease...

    KiNNik5 pointsBadges:
  • Ports Configuration for 2811 as a Terminal Server

    Is there any possible way to disable ports on a Cisco 2811 router that is configured as a terminal server

    SRR5 pointsBadges:
  • How do I get into the switch portion of a Cisco 2811 if I forgot the password?

    How do I get into the switch portion of a Cisco 2811 if I forgot the password

    Oneofknowledge5 pointsBadges:
  • Cisco 2811 VLAN Usage

    I inherited a network that has a Cisco 2811 router setup with the following: interface FastEthernet0/0 no ip address no ip route-cache cef no ip route-cache duplex full speed 100 ! interface FastEthernet0/0.18 description Data VLAN encapsulation dot1Q 18 native ip address 10.221.18.1 255.255.255.0...

    Zwitter1535 pointsBadges:
  • Cisco 2811 config

    Hi guys, I have two Cisco 2811 routers. Each of them has 2 Fast Ethernet and 1 Serial interfaces. I have two WAN connections on each router. One of them via FastEthernet0/0 and another one via Serial. I try to connect these two routers with redundancy scheme. For example, if primary connection...

    Fds19895 pointsBadges:
  • Cisco 2811 PVDM2-24DM Initialising

    Dear All Professionals, We have taken on the installation of a Cisco 2811 to make digital communications over ISDN and are requiring assistance with our hardware configuration . We have all the necessary modules and so on however our current problem is: We have the digital modem module in slot 0...

    Jtrade5 pointsBadges:
1

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following