• Monitoring network end user operation with a Cisco router

    Hi, One of my client requires a solution for monitoring end users traffic going through a Cisco router. There is a lot of problem with over utilization of WAN link by end users. The company need a solution for monitoring operation of end users (who & where they are trying to communicate)....

    Puli45 pointsBadges:
  • What does this command means in 1841 router configuration?

    What does this command mean in 1841 router configuration: "ip admission max-nodata-conns 3"?

    Florish5 pointsBadges:
  • Cisco Router 1841, will not Recongnise IP HTTP secure-server command

    I want to install SDM on my Cisco 1841 router, but the router will not recognize IP HTTP secure-server command, but I still manage to install the SDM on the router now I cannot configure the VPN because is not available i think due to wrong iOS release on the router.please how can I update it or...

    Olu15 pointsBadges:
  • I want a autofallback of link from BGP to OSPF

    Hi , I have a cisco 1841 router connected to 2 different isp & running 2 different protocol (ospf & bgp). I want to use ospf link as a primary & auto switch to bgp link in case of pri link failure. I have added static route to make ospf link pri  & it works but unable to auto...

    Chandrakant5 pointsBadges:
  • Can not Connect PC to Cisco 1841 Router!

    Hello I have a 1841 router.It has two F/E ports.One of them is connected to an ADSL modem and the other to my PC through crossover RJ-45 cable.The problem is that the connection is not active and light are off.and also I get network disconnection icon in windows.I tested the PC with other networks...

    h17273130 pointsBadges:
  • Converting fron a cisco 1841 router to a Cisco 2900 router

    My IT group bought me a 2900 series router to replace my 1841.  How do I copy the program from the 1841 and paste it to the 2900?  The reason for the change is due to needing more external ports.

    wyowool5 pointsBadges:
  • Cisco 1841 NTP configuration and sync

    Hi, I have configured a cisco 1841 to sync with a ntp server. after entering the ntp command, show ntp status says that it is not yet synchronized but on show clock details shows that it is already configured based on the ntp server. These are the result of show commands and the running config show...

    Vlao5 pointsBadges:
  • VPN pass-through Cisco 1841

    Hi there,  I have zywall p1 behind our cisco 1841 and i'm trying to pass-through vpn on a cisco 1841. ZyWAll p1 is terminator on the inside network and its ip address is : 172.16.178.1. But, zywall p1 is not our device its from other agency with which we need to establish vpn. Here is my...

    Murgam5 pointsBadges:
  • Cisco 1841,SDM will not connect nor install

    I am trying to install a VPN Server on my Cisco 1841 router. When I try to connect SDM it will not connect. I tried reinstalling the SDM on the router, but it comes to a stage & says "copy operation failed". I tried to install VPN through CLI, but the CLI doesn't recognize the CRYPTO command. Need...

    Aslamalikhan25 pointsBadges:
  • How to view the data of Cisco router’s memory

    I want to view the data of the memory,for example,between 0x60001000-0x60002000,but i don't find the command that can solve it.Please help me.

    Djcsdjcs5 pointsBadges:
  • Cisco configuration

    i have newly setup cisco 1841 router and i didn't create user and its password i just want to know that its default user or password will expired after 15 days or not. it is necessary to create user or password or not

    Kaleemu5 pointsBadges:
  • Flows Data through a Pix 515E firewall

    The flows data originates from a Cisco 1841 router outside the firewall at 200.100.1.1 A 'show ip cache flow' and a packet cap outside the fw shows data flowing. The flows port in use is 2055. Inside the firewall is a local machine 10.10.19.4/16 to capture the data. But no data arrives. On the Pix...

    Pixteck20 pointsBadges:
  • Load balance on WAN interface using static router between two ISP

    By using static router, i need to configure two lease line of 3 mbps and failover

    Pranab12310 pointsBadges:
  • 3G – Creating a S2S VPN when the 3G card uses DHCP and not static?

    I have a 3G WIC card (HWIC-3G-GSM) in a Cisco 1841 and need to create an IPSEC tunnel to a Cisco ASA5520 Normally creating a S2S tunnel would be relatively easy if both peers used static IP's, however my 3G provider uses dynamic addressing. If I try and create an IPSEC S2S VPN peer on a...

    OrangeNewbie55 pointsBadges:
  • BSNL Exchange End Architecture for MPLS

    Dear All , I am new in the Networking Industry , Presently working in a large Bank and doing network Rollout . My question is , that what is the Architecture of BSNL exhange while deploying MPLS . The Branch side has A Cisco 1841 router , which is connected to V.35 Modem , then connected to G.703 ...

    Pprasoo5 pointsBadges:
  • Route map Cisco

    I have a cisco router 1841. It has 2 outside adsl interfaces, and an inside interface connected to local lan. I want to use the 1st adsl interface for http, ftp and the 2nd adsl interface for the rest of the internet traffic. Below is a sample of my configuration: interface FastEthernet0/0  ip...

    Meglo161020 pointsBadges:
  • ROUTER INTERFACE

    IN ROUTER , ON SERIAL INTERFACE I AM GETTING POO RELY 201/255       WHAT CAN BE PROBLEM

    VADERA10 pointsBadges:
  • Cisco router password

    I have 1841 cisco router and I forgot the password, so how i can reconfig the password agin

    Mohadbazzi47170 pointsBadges:
  • I want use a D-link Dir-600 router that will sit behind a Cisco router with 2 vlans

    I have an application where I have setup a Cisco 1841 router with 2 vlan connection's, I want to setup a wireless D-link DIR-600 wireless router on one of vlans so visiting venders can get to the internet without being on my network. Do I need to setup the D-Link router with any VLan...

    Shedman35 pointsBadges:
  • Cisco 1841 isdn config

    sir ihave cisco 1841 router . how can configuring isdn in bri port .how can i config static route

    Sriman5 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

REGISTER or login:

Forgot Password?
By submitting you agree to receive email from TechTarget and its partners. If you reside outside of the United States, you consent to having your personal data transferred to and processed in the United States. Privacy

Thanks! We'll email you when relevant content is added and updated.

Following