• Bandwidth estimation for EMC MirrorView

    I have a EMC clarion array at my primary site and one at my secondary site the distance is roughly 15 miles. I am using a product called Mirror ASync. which is a EMC array based replication tool. I have a RTO of 30 minutes. data rate of change is aprox. 50 GB per day how much bandwidth should I...

    Rickfalcetta5 pointsBadges:
  • How to rate limit on Cisco Catalyst 3550-EMI

    Hello, I have a cisco switch 3550 EMI and I need to do rate limiting on ethernet ports. class-map match-all 5M description 5M with 500K burst ! policy-map 5M class 5M police 5120000 51200 exceed-action drop interface FastEthernet0/3 switchport access vlan 100 switchport mode dynamic desirable speed...

    SupermanInNY5 pointsBadges:
  • Wireless bridge

    My office runs a normal LAN. The company has recently purchased the building next door, and we want to extend the LAN into this building using a wireless link. To achieve this, we have purchased 2 Netgear WPN802 wireless access points. The Netgear website has a step by step guide to configuring the...

    Nickc197665 pointsBadges:
  • TCP Retransmissions b/c of Checksum Incorrect

    We have a problem where some users will complain of slow application response time (on the LAN) from our ERP server, but others will be fine. After many hours of troublshooting I've discovered the following: - Packet Sniff's of affected users shows TCP Retransmissions because the Checksum is...

    Tbitner510 pointsBadges:
  • Is it possible to lift router-based bandwidth caps (if they exist)?

    like the title says, is it possible to lift a router based bandwidth cap (if one exists) on my router. im only pulling about 100kb/s on a DSL line. i dont have a wireless setup running, jus straight cat-5 from the router to my cpu. i would assume capping would be done server side, but someone said...

    Stress5 pointsBadges:
  • Network Management

    I have 4mbps ADSL with over 100 user. I want to schedule the FTP traffic and HTTP traffic and wanted to maximize traffic for the management team. What should I do.

    Niftypiece10 pointsBadges:
  • ethernet bandwidth

    How does ethernet deliver different bandwidths?

    Dave L0 pointsBadges:
  • Protocol bandwidth load

    Is there an average estimated bandwidth load to use for each of the most common protocols (HTTP/HTTPS/POP3/IMAP/FTP/H.323)when calculating the total bandwidth needed b4 contracting the carrier?

    SBV5 pointsBadges:
  • Bandwidth Limit on Cisco 3550 catalyst switch on Fast ethernet

    Dear friend, I have a cisco 3350 catalyst switch, I want to limit bandith on that interface to 64kbps, I need help on this. I need to know another way of limiting the bandwith using access list on the ip address assigned to the host on that interface. send your replty to raj_741976@sify.com

    Somaraju5 pointsBadges:
  • Segmenting question

    How to segment a specific group on a network to have its own bandwidth without tremendously slowing down the rest of the network?

    MFDS075 pointsBadges:
  • Monitoring the Network

    Hi, I have multiple remote sites. I would like to monitor the network and analyze the traffic and its performance in general. For example, how the bandwidth is consumed, if certain activities are unnecessary and how to improve the networks performance by blocking through the firewall like...

    Maryam82100 pointsBadges:
  • How to derive bandwidth from the frequency of Cat6 cables

    How do you derive bandwidth (bits per second) from the frequency of Cat6 cable (250MHz for example)? It is known that Cat6 can carry up to 1 Gbps.

    NetworkingATE1,545 pointsBadges:
  • wireless vlan

    hi all, is it possible to have one link from a switch to an access point and split the network into two networks a wireless network from the AP and a wired port for a user connected thru RJ45 and still keep it secured.

    92220990 pointsBadges:
  • ISA (find out the bandwidth)

    I need to know currently how many bandwidth used by evry individual on the ISA environment, is there any 3rd party software I can use to find out the bandwidth used by the client individually, or is there any option(s) available in ISA. Thanx.

    239069370 pointsBadges:
  • How to test the internet connection speed without putting any load and allocating bandwidth

    We do have a 10 MB internet connectivity, the speed is ok, I am monitoring the link using cacti and netflow. ISP----10 MB Link-------Cisco 3745 Router----Switch ----Firewall 525----DMZ Switch- ISA---- LAN Our bandwidth is under utilized, hence our average consumption is around 5 MB, half of our...

    Yasir Irfan6,940 pointsBadges:
  • Installation and updates

    Howdy folks, Tryin to keep things going around here....need some advice. I have Win2003 servers and Active Directory.....single domain....approx. 100 client computers.....one location. Am upgrading all computers from Office XP to Office 2003. My project: Install Office 2003 and all updates remotely...

    TheVyrys0 pointsBadges:
  • Limiting Bandwidth by IP range

    Our guest can access internet via Wireless using a guest account on our ntwork but they can't access the resources on the network. We are looking for a was to limit the amount of bandwidth(Guest IP Range) used by the guests so it's doens't affect our network

    Prince975 pointsBadges:
  • BGP4 and load balancing

    Is it possible to use BGP4 to aggregate the total available bandwidth into one virtual pipe? Example can I take two 3 meg independent internet connections and make a burstable 6 meg pipe?

    Dhdevlin0 pointsBadges:
  • Calculating bandwidth for daily video program

    I have a client that wants to produce a daily five-minute video program. I was thinking of streaming it in Flash. How do I calculate the bandwidth and transfer rate that I will need if I'm estimating 100,000 viewers a day? Thank you for your time.

    NetworkingATE1,545 pointsBadges:
  • Divide bandwidth

    Hi guys, I have on #1 comp a connection to the internet (ppp connection) with 2 NIC's: one for the ppp connection, 2nd for another computer. the 2nd computer gets it's internet connection through the 1st comp(WIN XP SP2 ) using ICS my question: how can i manage bandwidth evely so that the 1st...

    Torturedsoul35 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following