• Canon IR 3235 on AS/400 goes into pending mode won’t print

    I have a Canon Ir 3235 that stopped printing and went into a pending status mid print job. Its attached through a network and the other ms server can print and I can ping the address. I deleted and recreated the OUTQ and DEV description and it still goes to pending. I have seen this before when...

    DanABC20 pointsBadges:
  • Zebra Z4M setup on AS400

    Dear all, I need help setting up a configuration on an AS400 for a Zebra Z4M printer physically located on another site. I can ping it from my AS400 but when I do WRKWTR to check spool status everything I send stays in PND. The printer light flashes so it detects the print request but nothing comes...

    Ahmedahmed15 pointsBadges:
  • Print proof of delivery in AS/400

    How do I print a proof of delivery for shipment in AS/400?

    JULIETTEMOORE15 pointsBadges:
  • AS/400 Barcode

    I am in search of information for barcoding onthe AS/400. We would prefer not to purchase new printers. Can printing barcodes be done without using a graphical interface software package?

    NMK5 pointsBadges:
  • Difference between LAN Printing and Remote Printing

    Hi, In our shop, we need to get a user access to take printout from AS400 to a printer that is outside our office network. We proposed to create a virtual printer session and download the print output which can be printed in any printer to which the machine is connected. However, during this...

    Meetmeonline215 pointsBadges:
  • iSeries Print Spool File 3 Up

    We were printing 3x8 notices (continuous forms) on IBM 6262 printer. After upgrading to laser HP printers, the 3x8 notices print one to a page. The software vendor has offered no help citing that a program change was not warranted. How can I make these print 3 UP. I have tried changing the spool...

    435015 pointsBadges:
  • IPDS printer prints 2 copies of barcode page

    We have a homegrown program that prints a barcoded (6 0f 9) page. I have ran tests and the spool file has only one page of data and is set to 1 copy. When we send the report to an IPDS printer (HP-4050) it prints two copies. Why should it do this? All other reports sent to this printer are normal....

    azohawk2,565 pointsBadges:
  • AS400 spool file printing twice

    AS400 - 820 - V5R3V0 - I have a couple of printers, Genicom line printers, when a request is sent to print a report about 5 minutes later the same report is printed again. These are interactive jobs requesting this report. I have checked everywhere I can think of and can not find a reason for this....

    Dlc21140010 pointsBadges:
  • Overlay and ‘print’ as pdf. Overlay not included !

    This statement OVRPRTF   FILE(MYPRTF)  DEVTYPE(*AFPDS) TOSTMF('/myapp/mypdfs')  WSCST(*PDF) beatifully generates a .pdf file and places it in the IFS-folder '/myapp/mypdfs'. ( ref:  http://www-01.ibm.com/support/docview.wss?uid=nas12bd8020c496ae912862575f400640da6  ) I have an overlay which I...

    DanTheDane2,555 pointsBadges:
  • AS/400 Group Jobs being held after the first empty job is run

    I am using STRGRPJS JOB to submit a group job but after the first job is run which is a empty job the remaining jobs are being held. Can anyone tell what should i do so that they don't go in held state? Thanks.

    aceamar25 pointsBadges:
  • AS/400 print files stuck at RDY

    I am managing, but very unfamiliar with AS/400. I have a user who does not receive the printouts for her job. It looks as though the printouts are all stuck in RDY status on the Output Queue. If I look at our printers, there is a printer of the same name as the Output Queue. That printer is in END...

    HeyLeonardo5 pointsBadges:
  • Printing separator pages with job number, user name etc

    Our print spool files print with separator pages. They seem to print based on user profiles. I cannot find it in the user profile descriptions or in the output queue descriptions. Is it possible to define them some where else?

    Gundu5 pointsBadges:
  • iSeries Report printing to network printer – font too small

    We have an AS/400 print file which is defined with: 10 CPI, 6 Lines per Inch, Width of 132, Length 66, Font Identifier is *CPI. We were using an AS400 print emulation session to print the report but want to get rid of this and use a device/outq on the as400. The report prints to a networked HP4050...

    Lehanb30 pointsBadges:
  • AS/400: Keyboard shortcut, send print screen to spool

    I've used a keyboard shortcut in the past to print screen to spool instead of local printer. Can't remember what the shortcut was or where I saw it. Anyone know what it is or how to find it?

    jlbeach795 pointsBadges:
  • iSeries V7R1 print files username

    We are printing jobs from our OUTQ to RICOH and they are good. But we're experiencing issues when trying to account jobs per user. When we go to printer panel we have job info/details and user/owner field. But here we can't see our system logged in user, so we cant see which user printed that job....

    iprint30 pointsBadges:
  • Printing useless pages overnight

    We recently installed an HP M605 printer on our network that is dedicated to iSeries use (no other network printing is permitted). Sometime between when we leave at night and come back in the morning this printer is spewing out about 15 pages with symbols (black twisty, happy face, happy face,...

    azohawk2,565 pointsBadges:
  • Users connected to a particular printer device in AS/400

    How can we find out who are the users connected to a particular printer device in AS/400 if we know the printer device name.

    dineshiseries555 pointsBadges:
  • AS/400 printing – DDS spec PAGRTT in record format definitions

    What do they mean when they say you must be 'on the page boundary' for this keyword (PAGRTT) to function? How can I check if I'm there or not? I would like to have one page in my printer file print portrait and the next in landscape, but PAGRTT doesn't work.

    JohnnyMooch35 pointsBadges:
  • AS/400 printing blank pages

    Why does AS/400 print a blank page with each print job to Canon printer?

    ghensarling5 pointsBadges:
  • Printing from an AS/400 to D-link wireless print server

    Hi all :) I have installed a D-link DPR-1040 wireless print server to an HP LaserJet via USB in our warehouse. I have set up the printer on a PC and can print to it from windows fine but cannot print from our AS/400. Has anyone been through this or similar issues? All help appreciated. Thanks, Tracy

    TracyGS70 pointsBadges:

Forgot Password

No problem! Submit your e-mail address below. We'll send you an e-mail containing your password.

Your password has been sent to:

To follow this tag...

There was an error processing your information. Please try again later.

Thanks! We'll email you when relevant content is added and updated.

Following